Abstract:Polyether ether ketone (PEEK) is introduced as a material for the additive manufacturing process called fused filament fabrication (FFF), as opposed to selective laser sintering (SLS) manufacturing. FFF manufacturing has several advantages over SLS manufacturing, including lower initial machine purchases costs, ease of use (spool of filament material vs powder material), reduced risk of material contamination and/or degradation, and safety for the users of the equipment. PEEK is an excellent candidate for FFF due to its low moisture absorption as opposed to other common FFF materials, such as Acrylonitrile Butadiene Styrene (ABS). PEEK has been processed into a filament and samples have been manufactured using several build orientations and extrusion paths. The samples were used to conduct tensile, compression, flexural, and impact testing to determine mechanical strength characteristics such as yield strength, modulus of elasticity, ultimate tensile strength and maximum elongation, etc. All tests were conducted at room temperature. A microscope analysis was also conducted to show features on the failures surfaces. The mechanical property results from this study are compared to other published results using traditional thermo-plastic manufacturing techniques, such injection molding. Tensile testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average ultimate tensile stresses were determined to be 73 MPa for 0° orientation, and 54 MPa for 90° orientation, with alternating 0°/90° orientations of 66.5 MPa. Compression testing was conducted at two raster orientations, 0° and alternating between 0° and 90°. Average ultimate strength for the single orientation direction was 80.9 MPa with the alternating orientations at 72.8 MPa. Flexural testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Ultimate flexural stress was determined to be 111.7 MPa for 0°, 79.7 MPa for 90°, and 95.3 MPa for orientations alternating between 0° and 90°. Finally, impact testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average impact energy absorbed was determined to be 17.5 Nm in the 0° orientation, 1.4 Nm in the 90° orientation, and 0.7 Nm for the alternating 0° and 90° orientations.

Material Extrusion 3D Printing of PEEK-Based Composites

Effect of Annealing and Carbon Nanotube Infill on the Mechanical and Electrical Properties of Additively Manufactured Polyether-Ether-ketone Nanocomposites Via Fused Filament Fabrication

High-performance carbon fiber reinforced polyether-ether-ketone composite pellets 3D-Printed via screw-extrusion additive manufacturing

A novel printing strategy to fabricate polyetheretherketone (PEEK)-based composites via hollow filaments filled with multiple reinforcements

Preparation of CCF/PEEK Filaments Together with Property Evaluation for Additive Manufacturing

High-strength carbon fiber-reinforced polyether-ether-ketone composites with longer fiber retention length manufactured via screw extrusion-based 3D printing

Superior strength in the 3D ‐printed polyether‐ether‐ketone composites reinforced by annealing and carbon fibers

Effect of Fiber Content on Mechanical Properties of Carbon Fiber-Reinforced Polyether-Ether-ketone Composites Prepared Using Screw Extrusion-Based Online Mixing 3D Printing

Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing

Polyether Ketone Ketone (PEKK) matrix composites for material extrusion additive manufacturing

Development and Processing of Continuous Flax and Carbon Fiber-Reinforced Thermoplastic Composites by a Modified Material Extrusion Process

EFFECTS OF EXTRUSION RATE AND POST-ANNEALING ON MECHANICAL PROPERTIES AND PRINTING QUALITY OF ADDITIVELY MANUFACTURED CARBON FIBER REINFORCED POLYETHERKETONEKETONE (PEEK) PARTS

Mechanical Properties of Additively Manufactured PEEK Components Using Fused Filament Fabrication

Effects of Printing Parameters of Fused Deposition Modeling on Mechanical Properties, Surface Quality, and Microstructure of PEEK

3D-Printed high performance PEEK/CF-PEEK polymer composites—An investigation on microstructural characteristics and mechanical performance

Enhanced Impregnation Behavior and Interfacial Bonding in CF/PEEK Prepreg Filaments for 3D Printing Application

Optimizing the Rheological and Thermal Behavior of Polypropylene-Based Composites for Material Extrusion Additive Manufacturing Processes

Thermo-oxidative crosslinking of carbon fiber reinforced PEEK (Polyetheretherketone) for additive manufactured ceramic matrix composites

Multifunctional performance of carbon nanotubes and graphene nanoplatelets reinforced PEEK composites enabled via FFF additive manufacturing

Impregnation and Interlayer Bonding Behaviours of 3D-Printed Continuous Carbon-Fiber-reinforced Poly-Ether-ether-ketone Composites