Abstract:Polyether ether ketone (PEEK) is introduced as a material for the additive manufacturing process called fused filament fabrication (FFF), as opposed to selective laser sintering (SLS) manufacturing. FFF manufacturing has several advantages over SLS manufacturing, including lower initial machine purchases costs, ease of use (spool of filament material vs powder material), reduced risk of material contamination and/or degradation, and safety for the users of the equipment. PEEK is an excellent candidate for FFF due to its low moisture absorption as opposed to other common FFF materials, such as Acrylonitrile Butadiene Styrene (ABS). PEEK has been processed into a filament and samples have been manufactured using several build orientations and extrusion paths. The samples were used to conduct tensile, compression, flexural, and impact testing to determine mechanical strength characteristics such as yield strength, modulus of elasticity, ultimate tensile strength and maximum elongation, etc. All tests were conducted at room temperature. A microscope analysis was also conducted to show features on the failures surfaces. The mechanical property results from this study are compared to other published results using traditional thermo-plastic manufacturing techniques, such injection molding. Tensile testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average ultimate tensile stresses were determined to be 73 MPa for 0° orientation, and 54 MPa for 90° orientation, with alternating 0°/90° orientations of 66.5 MPa. Compression testing was conducted at two raster orientations, 0° and alternating between 0° and 90°. Average ultimate strength for the single orientation direction was 80.9 MPa with the alternating orientations at 72.8 MPa. Flexural testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Ultimate flexural stress was determined to be 111.7 MPa for 0°, 79.7 MPa for 90°, and 95.3 MPa for orientations alternating between 0° and 90°. Finally, impact testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average impact energy absorbed was determined to be 17.5 Nm in the 0° orientation, 1.4 Nm in the 90° orientation, and 0.7 Nm for the alternating 0° and 90° orientations.

In-house processing of 3D printable polyetheretherketone (PEEK) filaments and the effect of fused deposition modeling parameters on 3D-printed PEEK structures

Research on Internal Filling Technology of 3D Printing PEEK

Effects of Printing Parameters of Fused Deposition Modeling on Mechanical Properties, Surface Quality, and Microstructure of PEEK

In-house processing of carbon fiber-reinforced polyetheretherketone (CFR-PEEK) 3D printable filaments and fused filament fabrication-3D printing of CFR-PEEK parts

Mechanical Properties of Additively Manufactured PEEK Components Using Fused Filament Fabrication

On Mechanical, Physical, and Bioactivity Characteristics of Material Extrusion Printed Polyether Ether Ketone

Tensile and Bending Strength Improvements in PEEK Parts Using Fused Deposition Modelling 3D Printing Considering Multi-Factor Coupling

Mechanical Properties Optimization of Poly-Ether-Ether-Ketone Via Fused Deposition Modeling.

Effect of process parameters of fused deposition modeling on mechanical properties of poly-ether-ether-ketone and carbon fiber/poly-ether-ether-ketone

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Effect of molecular weight on mechanical properties and microstructure of 3D printed poly(ether ether ketone)

Influence of Layer Thickness and Raster Angle on the Mechanical Properties of 3D-Printed PEEK and a Comparative Mechanical Study between PEEK and ABS

Effects of processing parameters and annealing on the mechanical properties of polyether ether ketone(PEEK) via fused deposition modeling(FDM)

Experimental investigation of process parameters in polyether ether ketone 3D printing

Impact Strength of 3D Printed Polyether-ether-ketone (PEEK)

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Taguchi-Based Experimental Investigation and Modeling of 3D-Printed PEEK Parts as Biomedical Implants using Fused Deposition Modeling for Improving Mechanical Strength and Surface Quality

EFFECTS OF EXTRUSION RATE AND POST-ANNEALING ON MECHANICAL PROPERTIES AND PRINTING QUALITY OF ADDITIVELY MANUFACTURED CARBON FIBER REINFORCED POLYETHERKETONEKETONE (PEEK) PARTS

3D-Printed high performance PEEK/CF-PEEK polymer composites—An investigation on microstructural characteristics and mechanical performance

Influence of Thermal Processing Conditions on Mechanical and Material Properties of 3D Printed Thin-Structures Using PEEK Material