Abstract:We present a solid‐state processing pathway for ultrahigh molecular weight polyethylene, a high‐end engineering polymer that cannot be melt processed. Ultra‐high molecular weight polyethylene (UHMWPE) stands out as the preferred material across a wide spectrum of demanding applications, thanks to its remarkable mechanical, chemical and physical attributes. Nevertheless, processing UHMWPE can be an arduous and time‐consuming endeavor. Traditional melt‐processing techniques, commonly employed for polymers, prove impractical due to the exceedingly high viscosity of the melt that follows from the highly entangled macromolecular chains. Several methods are known to lower the entanglement density of UHMWPE, such as crystallization from a semidilute solution or direct polymerization, resulting in a less interconnected polymer structure. Unfortunately, even with low‐entangled UHMWPE, melt processing remains unviable because of the rapid re‐entanglement of polymer chains upon melting. However, these low‐entangled UHMWPE materials can still be effectively processed in the solid state, a technique employed in the production of high‐performance UHMWPE fibers and tapes, currently the only two feasible geometries. This research reports the development of a solid‐state extrusion method for nascent low‐entangled powder, centering on manipulating the surface energy of the interior wall materials within the extruder and die. Ordinary steel dies proved ineffective for solid‐state extrusion, as they generated excessive friction between the die and UHMWPE, resulting in a rapidly escalating extrusion pressure. However, utilizing dies constructed from temperature‐resistant polymers allowed for extrusion at a consistent pressure without the need for lubricating agents. We demonstrate the practicality of the developed solid‐state extrusion method by fabricating UHMWPE monofilaments and tubes, showcasing its potential in expanding the range of producible UHMWPE geometries. Additionally, a first evaluation of the influence of processing conditions and the entanglement density of the reactor powder used on extrudability, and the properties of the resulting components is presented. Highlights A process for the solid‐state extrusion of UHMWPE is developed. UHMWPE processing with higher design flexibility than current industrial standards. UHMWPE processing with higher throughput than current industrial standards. Contrary to previous techniques no lubricating agent or co‐extrudate is used.

Structure and properties of ultrahigh molecular weight polyethylene processed under a consecutive elongational flow

Rheology of Ultra High Molecular Weight Polystyrene

Enhancing Chain Mobility of Ultrahigh Molecular Weight Polyethylene by Regulating Residence Time under a Consecutive Elongational Flow for Improved Processability

Elongational Flow Field Processed Ultrahigh Molecular Weight Polyethylene/Polypropylene Blends with Distinct Interlayer Phase for Enhanced Tribological Properties

Thermal and Mechanical Properties of Ultrahigh-Molecular-Weight Ethylene/1-Hexene Copolymers Prepared by Living Polymerization with Fluorinated Bis(Phenoxy-Imine) Titanium(Iv) Catalyst

Solid‐state extrusion of nascent disentangled ultra‐high molecular weight polyethylene

Chain conformation and dynamics in ultrahigh molecular weight polyethylene melts undergoing extensional–shear coupled flow: insight from dissipative particle dynamics simulation

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Flow‐field‐assisted Shaping of Linear Low‐density Polyethylene/low‐entanglement Ultra‐high Molecular Weight Polyethylene Blends with Enhanced Mechanical Properties and Thermal Conductivity

Towards high-performance all-polyethylene materials by a two-step processing strategy using two-roll mill

Influence of Reduced Graphene Oxide on the Rheological Response and Chain Orientation on Shear Deformation of High Density Polyethylene

Dynamic rheological behavior, crystallization and friction performance of ultrahigh molecular weight polyethylene/polypropylene blends by multi-step melt processing strategy

Weakly Entangled Ultrahigh Molecular Weight Polyethylene Prepared via Ethylene Extrusion Polymerization

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Heterogeneous Distribution of Entanglements in a Nonequilibrium Polymer Melt of UHMWPE: Influence on Crystallization Without and with Graphene Oxide

Unusual Rheological Behaviors of Linear Pe and Pe/Kaolin Composite

Enhancing Gel Spinning of Ultra-High Molecular Weight Polyethylene: Insights into Rheology and Microstructure

The rheology of ultra-high molecular weight poly(ethylene oxide) dispersed in a low molecular weight carrier

Ultra-high molecular weight polyethylene (UHMWPE)/high-density polyethylene (HDPE) blends with outstanding mechanical properties, wear resistance, and processability

Unique Morphology of Polylactide/Poly(ε-Caprolactone) Blends Extruded by Eccentric Rotor Extruder

Dissolving of Ultra-high Molecular Weight Polyethylene Assisted Through Supercritical Carbon Dioxide to Enhance the Mechanical Properties of Fibers