Abstract:Schematic of sequential melting and sintering process on morphology development of UHMWPE/LDPE blends. Blending ultra‐high molecular weight polyethylene (UHMWPE) with a low molecular weight polyolefin is a well‐established technique to improve its processability. The binary blends of UHMWPE and low‐density polyethylene (LDPE) were prepared with varying LDPE content (10%, 20%, 30%, 40%, and 50% by wt.) leading to the formation of a single polymer composite system (SPCS) as melting and sintering followed preferential stages during mixing. Interestingly, the sequence of either "melting followed by sintering" or "simultaneous sintering and melting" depends on the LDPE content in the blend, resulting in unique blend morphology. Separate melting peaks for the blend's constituents were observed in thermal characterization, showing the blend's immiscibility, while intermediate peaks showed moderate miscibility in the melt state. Due to the high entanglement density, UHMWPE retained a solid‐like structure and showed an intense viscous nature even above the melting point in rheological characterization. Typically, the UHMWPE samples are fabricated by boundary fusion between particles called sintering. At LDPE content higher than 30 wt.%, the sea island structure was visible in morphological analysis, and the preexisting cavities reduced the tensile modulus by 54% in the blend, along with decreased elongation at failure (250%–100%). Similarly, the flexural modulus was reduced by 34.7% in the blends, along with the decreased flexural strength. Interestingly, the decrease in performance properties occurred in two steps over the range of LDPE content. Thus, it was clear that 30 wt.% of LDPE in the UHMWPE/LDPE blend represented the critical concentration for controlling melting and sintering sequence to develop specified morphology and performance properties. These blends have the potential for biomedical application as well as for the development of foam products, which is the further scope of the present study.

Short-time fabrication of well-mixed high-density polyethylene/ultrahigh-molecular-weight polyethylene blends under elongational flow: morphology, mechanical properties and mechanism: Fabrication and performance of HDPE/UHMWPE blends under elongational flow

Ultra-high molecular weight polyethylene (UHMWPE)/high-density polyethylene (HDPE) blends with outstanding mechanical properties, wear resistance, and processability

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Elongational Flow Field Processed Ultrahigh Molecular Weight Polyethylene/Polypropylene Blends with Distinct Interlayer Phase for Enhanced Tribological Properties

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Effect of Entangled State of Nascent UHMWPE on Structural and Mechanical Properties of HDPE/UHMWPE Blends

Enhancing Chain Mobility of Ultrahigh Molecular Weight Polyethylene by Regulating Residence Time under a Consecutive Elongational Flow for Improved Processability

Flow‐field‐assisted Shaping of Linear Low‐density Polyethylene/low‐entanglement Ultra‐high Molecular Weight Polyethylene Blends with Enhanced Mechanical Properties and Thermal Conductivity

In Situ Synthesized Self-Reinforced HDPE/UHMWPE Composites with High Content of Less Entangled UHMWPE and High Gradient-Distributed Oriented Structures

Dynamic rheological behavior, crystallization and friction performance of ultrahigh molecular weight polyethylene/polypropylene blends by multi-step melt processing strategy

Melt blending of commercial linear polyethylene with low-entangled ultra-high molecular weight polyethylene: from dispersion compatibility to viscoelastic scaling laws

Influence of sequential melting and sintering process on morphology development and performance properties of ultra‐high molecular weight polyethylene/low‐density polyethylene blends

Blending Ultrahigh‐molecular‐weight Polyethylene and Poly(ethylene/10‐undecen‐1‐ol) in One Nascent Particle

Preparation and Characterization of Electrospun Mat of Ultra-high Molecular Weight Polyethylene/High-Density Polyethylene Blends

Rheological Behavior and Mechanical Properties of High‐density Polyethylene Blends with Different Molecular Weights

Constructing highly oriented and condensed shish-kebab crystalline structure of HDPE/UHMWPE blends via intense stretching process:Achieving high mechanical properties and in-plane thermal conductivity

Blending Recycled High-Density Polyethylene HDPE (rHDPE) with Virgin (vHDPE) as an Effective Approach to Improve the Mechanical Properties

Abrasive wear of HDPE/UHMWPE blends

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends