Abstract:Copper Zinc Tin Sulfide (Cu2ZnSnS4 or CZTS) is gaining much attention recently as a potential light absorber alternative to CuInGaSe2 due to its suitable energy band gap ∼1.5 eV with p-type conductivity, high optical absorption coefficient of ∼105 cm−1. Moreover, all its constituents are abundant in the crust of the earth and environmentally harmless. In the present investigation, CZTS thin films were prepared using simple two step process of, sulfurization of sequentially sputtered stack, Glass/Zn/Sn/Cu (hereafter CTZ) metallic precursors on soda lime glass substrate held at temperature 200 °C. The sputter power was optimized individually for Zn, Sn, and Cu layers. The sputtered CTZ precursors were annealed at different temperatures in the range, 300–550 °C with an increment of 50 °C for 2 h in the ambience of vaporized elemental sulfur. The XRD pattern revealed that the films sulfurized in the temperature range 300–400 °C showed various spurious (binary and ternary) phases and the films sulfurized at 450 °C exhibited a clear phase corresponding to CZTS that becomes predominant at 500 °C. The optimized (500 °C) CZTS thin films showed kesterite structure with (112) preferred orientation. The sharp Raman shift centered at 336 cm−1 confirms the single phase CZTS for the precursors sulfurized at 500 °C. From the transmittance measurements, the energy gap is found to be 1.62 eV for optimized CZTS films. The optical profilometer studies indicated an increase in the surface roughness with the sulfurization temperature. AFM measurements revealed compact morphology with pyramidal texture.

Synthesis and Characterizations of Cu2MgSnS4 Thin Films with Different Sulfuration Temperatures

Phase composition of the earth-abundant Cu2SnS3 thin films with different annealing temperature and its effects on the performance of the related solar cells

Synthesis, Growth and Characterization of Cu2CoSnS4 Thin Films via Thermal Evaporation Method

Sulfurization Temperature Dependent Physical Properties of Cu2SnS3 Films Grown by a Two-Stage Process

Investigation of the Sulfurization Process of Cu2sns3 Thin Films with Stacked Layers Cbd-Cu/Sns by Rapid Thermal Process

Effect of the stacking order, annealing temperature and atmosphere on crystal phase and optical properties of Cu2SnS3

Fabrication of Cu2SnS3 Thin Film Solar Cells Via a Sol-Gel Technique in Air

Preparation and properties of Cu2 MgSnS4 thin films and fabrication of heterojunction devices

The Properties of the Earth Abundant Cu2SnS3 Thin Film Prepared by Spray Pyrolysis and Rapid Thermal Annealing Route

Physical Properties of Cu2SnS3 Thin Films Prepared by Sulfurization of Co-Sputtered Cu-Sn Metallic Precursors

Preparation of High-Quality Cu2ZnSnS4 Thin Films for Solar Cells Via the Improvement of Sulfur Partial Pressure Using a Static Annealing Sulfurization Approach

Influence of Sulfurization Temperature on Physical Properties of Cu2znsns4 Thin Films

Preparation and Characterization of Cu2SnS3 Thin Films by Two Stage Process for Solar Cell Application

Synthesis and Characterization of Cu 2 ZnSnS 4 from Cu 2 SnS 3 and ZnS Compounds

EFFECT OF ANNEALING ON THE CuInS2 THIN FILMS PREPARED BY CHEMICAL BATH DEPOSITION

Dependence of the properties of copper zinc tin sulfide thin films prepared by electrochemical deposition on sulfurization temperature

Optical and Electrical Investigations on Cu2SnS3 Layers Prepared by Two-Stage Process

Optical and Electrical Properties Study of Sol-Gel Derived Cu2znsns4 Thin Films for Solar Cells

Fabrication and Photoelectric Properties of Cu2FeSnS4(CFTS) and Cu2FeSn(S,Se)4(CFTSSe) Thin Films

Fabrication of Cu 2 SnS 3 thin-film solar cells with oxide precursor by pulsed laser deposition

Effect of post sulfurization temperature on the microstructure of Cu2ZnSn(S,Se)4 thin film