Abstract:ZG25MnCrNiMo steel samples were prepared by squeeze casting under pressure ranging from 0 to 150 MPa. The effects of pressure on the microstructure, low-temperature toughness, hardness, and impact wear performance of the prepared steels were experimentally investigated. The experimental results indicated that the samples fabricated under pressure exhibited finer grains and a significant ferrite content compared to those produced without pressure. Furthermore, the secondary dendrite arm spacing of the sample produced at 150 MPa decreased by 45.3%, and the ferrite content increased by 39.1% in comparison to the unpressurized sample. The low-temperature impact toughness of the steel at −40 °C initially increased and then decreased as the pressure varied from 0 MPa to 150 MPa. And the toughness achieved an optimal value at a pressure of 30 MPa, which was 65.4% greater than that of gravity casting (0 MPa), while the hardness decreased by only 6.17%. With a further increase in pressure, the impact work decreased linearly while the hardness increased slightly. Impact fracture analysis revealed that the fracture of the steel produced without pressure exhibited a quasi-cleavage morphology. The samples prepared by squeeze casting under 30 MPa still exhibited a large number of fine dimples even at −40 °C, indicative of ductile fracture. In addition, the impact wear performance of the steels displayed a trend of initially decreasing and subsequently increasing across the pressure range of 0–150 MPa. The wear resistance of samples prepared without pressure and at 30 MPa was superior to that at 60 MPa, and the wear resistance deteriorated when the pressure increased to 60 MPa, after which it exhibited an upward trend as the pressure continued to rise. The wear mechanisms of the samples predominantly consisted of impact wear, adhesive wear, and minimal abrasive wear, along with notable occurrences of plastic removal, furrows, and spalling.

Effect of Applied Pressure on Microstructures of Squeeze Cast Mg–15Gd–1Zn–0.4Zr Alloy

Influence of Pressure and Temperature on Microstructure and Mechanical Behavior of Squeeze Cast Mg-10Gd-3Y-0.5Zr Alloy

Influences of Heat Treatment on Microstructural Evolution and Tensile Behavior of Squeeze-Cast Mg–Gd–Y–Zr Alloy

Experimental study of squeeze casting of ZK60 magnesium alloy

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Effects of Pressure and Aging Treatment on Microstructures and Mechanical Properties of Rheo-Squeeze Casting Mg–3Nd–0.2Zn–0.4Zr Alloy

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

The influence of hot isostatic pressing on precipitates, mechanical properties of Mg-12Gd-0.8Zn-0.4Zr (wt.%) alloy manufactured by sand casting

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D

Squeeze Cast Mg-Zn Alloys for Bioapplications: Tensile Properties and Microstructure

Effects of Process Parameters on the Macrostructure of a Squeeze-Cast Mg-2.5 Mass%nd Alloy

Study on the Effect of Pressure on the Microstructure, Mechanical Properties, and Impact Wear Behavior of Mn-Cr-Ni-Mo Alloyed Steel Fabricated by Squeeze Casting

Mechanical Behavior and Microstructure Evolution of Mg-Gd-Y-Zn-Zr Alloy during Multipass Hot Compression Deformation

Microstructure and Mechanical Properties of Squeezing Casting Mg-Nd-Gd-Zn-Zr Alloy

Effects of processing parameters on microstructure and mechanical properties of squeeze-cast Mg–12Zn–4Al–0.5Ca alloy

Microstructure evolution and mechanical properties of an ultra-high strength casting Mg–15.6Gd–1.8Ag–0.4Zr alloy

Microstructural Evolution and Mechanical Properties of Al–Si–Cu–(Ge)–(Mg) Alloy Solidified under High Pressure

Study on Dendritic Growth in Pressurized Solidification of Mg–Al Alloy Using Phase Field Simulation

Improvements of Elevated Temperature Tensile Strengths of Mg-Gd-Y-Zr Alloy Through Squeeze Cast

Effects of Runner Design and Pressurization on the Microstructure of a High-Pressure Die Cast Mg-3.0Nd-0.3Zn-0.6Zr Alloy

Effects of different holding pressures on the microstructure and mechanical properties of Al-5.9Zn-2.2Mg-1.8Cu alloy