Abstract:Pressure is, like temperature, a basic thermodynamic variable which can be used to alter the matter state. The atom volume, free energy of matter and other physical and chemical properties can be changed due to the application of high pressure. Many interesting materials including superconducting, super-hard, amorphous, nanomaterials can be prepared under high pressures. Meanwhile, the application of high pressure during solidification of metallic materials has also attracted much attention of researchers in recent years. However, the understanding of high pressure on alloy solidification behavior is still lacked, and needs more experimental and theoretical investigation. In the present work, the effect of high pressure on solidification microstructure, phase constitution and mechanical properties of Al-20Mg alloy was investigated by OM, XRD and tensile test. Influence of solute distribution on mechanical properties of solid solution was analyzed and the corresponding mechanism was discussed based on the solute strengthening theory. The results showed that the amount of intermetallic compound beta-Al3Mg2 decreases and the amount of Al(Mg) solid solution increases in the Al-20Mg alloy solidified under high pressure, resulting in the remarkable enhancement of the mechanical properties. The Al-20Mg alloy is fragile under 1.0 x 10(5) Pa. However, it can transform to be a ductile material with elongation of 11% when solidified under 2 and 3 GPa. Meanwhile, its strength can be also greatly improved. The ultimate tensile strength of Al-20Mg alloy solidified under 2 GPa is 8.9 times of that solidified under 1.0x10(5) Pa. The yield strength of Al-20Mg alloy solidified under 2 GPa is higher than that under 3 GPa. This phenomenon was explained by solute strengthening theory, and proved that the inhomogeneous distribution of Mg solute in the solid solution can enhance the mechanical properties. The fracture characteristic is essentially altered under the condition of high pressure solidification. The Al-20Mg alloy is cleavage fracture under 10(5) Pa, however, it transforms to the dimple fracture when solidified under 2 and 3 GPa. The present work provides a potential route to improve the mechanical properties of solid solution through the control of solute distribution in the solid solution.

Refinement and strengthening mechanism of Mg−Zn−Cu−Zr−Ca alloy solidified under extremely high pressure

Microstructural Evolution and Mechanical Properties of Al–Si–Cu–(Ge)–(Mg) Alloy Solidified under High Pressure

Enhancement of mechanical properties of Al–Mg alloy with a high Mg content solidified under high pressures

MECHANICAL BEHAVIOR OF Al-20Mg ALLOY SOLIDIFIED UNDER HIGH PRESSURE

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructural evolution and precipitation behavior of Al-7Si-3Cu alloy prepared under 5 GPa

Evolution of Microstructures and Phases of Al–Mg Alloy under 4 GPa High Pressure

High Pressure Solidification Microstructure and Stability of Al-9.6%Mg Alloy

Enhanced tensile properties in a high-pressure synthesized Al-Si-Cu-Ge-Mg alloy with nano-sized Al particles in eutectic Si

Microstructure evolution of Al–Mg alloy during solidification under high pressure

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Achieving high strength above 400 MPa in conventionally extruded Mg-Ca-Zn ternary alloys

Microstructure modification and precipitation strengthening for Mg–6Zn–1Mn–4Sn–0.5Ca through extrusion and aging treatment

Enhancing Mechanical Performances by Unconventional Si Precipitates Obtained in Pressure-Induced Al-Si-Cu-(Mg) Solid Solutions

Microstructure evolution and mechanical properties of an ultra-high strength casting Mg–15.6Gd–1.8Ag–0.4Zr alloy

Effects of different holding pressures on the microstructure and mechanical properties of Al-5.9Zn-2.2Mg-1.8Cu alloy

Microstructure evolution and precipitation of Al–12Mg alloy solidified under high pressure

Microstructural Characteristics and Mechanical Performances of Al–Si–Cu–Mg-(Ge) Alloys Prepared under 5Gpa-Level Pressure

Formation of high strength Mg–Cu–Zn–Y alloys

Theoretical insights into the crystal and fundamental properties of MgAl9Zn compound: First-Principles calculations

The effect of pressure-induced Mg64Zn15Y21 phase on the mechanical properties of Mg–Zn–Y alloy