Abstract:The hot deformation behaviors of single- and two-phase CuAlMn shape memory alloy were studied. Isothermal compression tests were conducted at different temperatures from 400<math>°C</math> to 800<math>°C</math> and various strain rates from 0.001/S to 1/S. At the temperature below 500<math>°C</math>, CuAlMn alloy had a two-phase microstructure (FCC <math>α</math> phase + <math>L21</math> <math>β</math> phase); while at the temperature higher than 550<math>°C</math>, the alloy had a single <math>β</math> phase structure. The flow stress curves showed the stress drop for all samples, indicating a dynamic recrystallization (DRX) feature of the alloy. The local minimum value of stress drop appeared at 500<math>°C</math>. The thermal active energy (<math>Q</math>) were calculated to be <math>418.7 kJ mol−1</math> for <math>α+β</math> alloy at 400–500<math>°C</math> and <math>219.7 kJ mol−1</math> for <math>β</math> alloy at 550–800<math>°C</math>, respectively. The artificial neural network (ANN) model showed a high precision to predict the flow stress of the studied alloy at a wide range of temperature. Based on the dynamic material model (DMM) theory, the processing map of the alloy that consists of the contour lines of the power dissipation factor, <math>η</math>, and the instability criteria was established. The grains were refined to a micron level and DRX of <math>α</math> phase occurred during the deformation between 400–500<math>°C</math> at the low strain rate. The hot deformation behaviors of the alloy at the low temperature (400–450<math>°C</math>) mainly depended on the deformation of <math>α</math> phase. The optimum deformation parameters for the single-phase CuAlMn alloys were 750–800<math>°C</math>/0.1–1 s−1.

Competitive Relationship Between Thermal Effect and Grain Boundary Precipitates on the Ductility of an As-Quenched Al–Cu–Mn Alloy

Temperature-dependent Constitutive Behavior with Consideration of Microstructure Evolution for As-Quenched Al-Cu-Mn Alloy

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Experiment and multiscale modeling of the coupled influence of constituents and precipitates on the ductile fracture of heat-treatable aluminum alloys

Effect of Precipitation During Quenching on the Prediction of the Mechanical Properties of Al-5 Pct Cu Alloy after T6 Treatment

High-Temperature Tensile Characteristics of an Al–Zn–Mg–Cu Alloy: Fracture Characteristics and a Physical Mechanism Constitutive Model

Microstructure Effects on Tensile Brittleness of As-Quenched Zl205A at Elevated Temperature

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Constitutive Behavior for Quenching of Al–Cu–Mg Alloy With Consideration of Precipitation

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy

Precipitated phase characteristics and fracture behaviour of cast Al–Cu–Mn alloy

Dynamic Softening Mechanism and an Improved Unified Constitutive Model for an Al–Cu–Mn–Fe–Zr Alloy during Warm Deformation

Study of rate-dependence at elevated temperature for an Al-Cu-Mg alloy

Experimental and Simulation Study for the Influence of Thermal Pre-Deformation on Subsequent Aging Precipitation Kinetics of Al-Zn-Mg-Cu Alloy

Temperature effect on tensile behavior of an interstitial high entropy alloy: Crystal plasticity modeling

Effect of quenching rate and its coupling model on precipitation and strength of Al–Cu–Cd alloys

A micromechanical study on the effects of precipitation on the mechanical properties of CoCrFeMnNi high entropy alloys with various annealing temperatures

Hot deformation behavior of a CuAlMn shape memory alloy

Deformation and Fracture Mechanisms of an Annealing-Tailored "bimodal" Grain-Structured Mg Alloy

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

Effects of cooling rate and cryogenic temperature on the mechanical properties and deformation characteristics of an Al-Mg-Si-Fe-Cr alloy