Abstract:The hot deformation behaviors of single- and two-phase CuAlMn shape memory alloy were studied. Isothermal compression tests were conducted at different temperatures from 400<math>°C</math> to 800<math>°C</math> and various strain rates from 0.001/S to 1/S. At the temperature below 500<math>°C</math>, CuAlMn alloy had a two-phase microstructure (FCC <math>α</math> phase + <math>L21</math> <math>β</math> phase); while at the temperature higher than 550<math>°C</math>, the alloy had a single <math>β</math> phase structure. The flow stress curves showed the stress drop for all samples, indicating a dynamic recrystallization (DRX) feature of the alloy. The local minimum value of stress drop appeared at 500<math>°C</math>. The thermal active energy (<math>Q</math>) were calculated to be <math>418.7 kJ mol−1</math> for <math>α+β</math> alloy at 400–500<math>°C</math> and <math>219.7 kJ mol−1</math> for <math>β</math> alloy at 550–800<math>°C</math>, respectively. The artificial neural network (ANN) model showed a high precision to predict the flow stress of the studied alloy at a wide range of temperature. Based on the dynamic material model (DMM) theory, the processing map of the alloy that consists of the contour lines of the power dissipation factor, <math>η</math>, and the instability criteria was established. The grains were refined to a micron level and DRX of <math>α</math> phase occurred during the deformation between 400–500<math>°C</math> at the low strain rate. The hot deformation behaviors of the alloy at the low temperature (400–450<math>°C</math>) mainly depended on the deformation of <math>α</math> phase. The optimum deformation parameters for the single-phase CuAlMn alloys were 750–800<math>°C</math>/0.1–1 s−1.

Temperature-dependent Constitutive Behavior with Consideration of Microstructure Evolution for As-Quenched Al-Cu-Mn Alloy

Modeling the Strain Rate-Dependent Constitutive Behavior in Nanotwinned Polycrystalline Metals

Competitive Relationship Between Thermal Effect and Grain Boundary Precipitates on the Ductility of an As-Quenched Al–Cu–Mn Alloy

Constitutive Behavior for Quenching of Al–Cu–Mg Alloy With Consideration of Precipitation

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Constitutive modeling and microstructure characterization of 2196 Al-Li alloy in various hot deformation conditions

The Flow Stress Behavior and Physical-Based Constitutive Model for As-Quenched Al-Zn-Mg-Cu Alloy

Dynamic Recrystallization Critical Conditions and a Physically–Based Constitutive Model of Al–4.8Mg Alloy Under Hot Working Conditions

Hot deformation behavior of a CuAlMn shape memory alloy

Dynamic Softening Mechanism and an Improved Unified Constitutive Model for an Al–Cu–Mn–Fe–Zr Alloy during Warm Deformation

Experiment and multiscale modeling of the coupled influence of constituents and precipitates on the ductile fracture of heat-treatable aluminum alloys

Microstructure Effects on Tensile Brittleness of As-Quenched Zl205A at Elevated Temperature

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

High-Temperature Tensile Characteristics of an Al–Zn–Mg–Cu Alloy: Fracture Characteristics and a Physical Mechanism Constitutive Model

Constitutive equation and dynamic recovery mechanism of high strength cast Al-Cu-Mn alloy during hot deformation

Investigation of deformation behavior and strain-induced precipitations in Al-Zn-Mg-Cu alloys across a wide temperature range

Hot Deformation Behavior of Homogenized Al-7.8Zn-1.65Mg-2.0Cu (wt.%) Alloy

Constitutive behavior and novel characterization of hot deformation of Al-Zn-Mg-Cu aluminum alloy for lightweight traffic

Study of rate-dependence at elevated temperature for an Al-Cu-Mg alloy

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy