Abstract:A novel method for calculating the critical resolved shear stress (CRSS) ratios of different deformation system types in polycrystalline non-cubic metals has been developed. The mean CRSS ratios between different deformation systems were calculated for both commercially pure (CP) Ti and Ti–5Al–2.5Sn (wt.%) tensile deformed at ambient temperature and 455°C using an in situ scanning electron microscope-based testing technique combined with electron backscattered diffraction. It was found that the relative activity of the different deformation systems changes as a function of alloying composition and deformation temperature. Prismatic slip was the most active deformation mode for CP Ti. CP Ti exhibited a lower resistance to prismatic slip at both ambient and elevated temperatures compared with Ti–5Al–2.5Sn. For Ti–5Al–2.5Sn, prismatic slip was the most active deformation system at ambient temperature although the basal slip activity significantly increased compared to CP Ti, mostly likely due to an increased c/a ratio resulting in a closer packed basal plane. At 455°C, basal slip exhibited a lower CRSS than prismatic slip for Ti–5Al–2.5Sn. The relative activity of other deformation systems was also affected by alloying and temperature. The statistical resampling technique of bootstrapping was used to generate multiple equivalent data sets from which mean CRSS ratios between different deformation systems, and associated confidence intervals, could be deduced. It was found that the mean CRSS ratios at low and high strains varied slightly for the same testing conditions. Moreover, lesser activated slip systems resulted in relatively larger confidence intervals for the CRSS means. This variability may be attributed to a number of potential factors, including measurement errors, rotations of grains during deformation, local stress state variations, and work hardening. The analysis further suggests that awareness of the intrinsic statistical variability in CRSS ratios should be considered when formulating crystal plasticity constitutive models.

In Situ SEM Study of Tensile Deformation of a Near-Β Titanium Alloy

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Plastic Deformation Mechanism and Slip Transmission Behavior of Commercially Pure Ti during In Situ Tensile Deformation

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Deformation Behavior and Tensile Properties of the Semi-Equiaxed Microstructure in Near Alpha Titanium Alloy

Deformation mechanisms in the α phase of the Ti-6Al-2Sn-4Zr-2Mo titanium alloy: in situ experiments and simulations

In situ EBSD study of the twinning deformation behaviors in pure titanium

In-Situ Study on Tensile Deformation and Fracture Mechanisms of Metastable β Titanium Alloy with Equiaxed Microstructure

The Action Mechanism of Rolling Texture on the Anisotropic Behavior of a Pure Titanium Plate

In Situ Electron Backscatter Diffraction Study of Deformation Inhomogeneity under Uniaxial Tension of Laser Melting Deposited TA15 Alloy

Slip initiation in interlayered β and corresponding slip transfer during compression of a lamellar-structure titanium alloy

Methodology for estimating the critical resolved shear stress ratios of α-phase Ti using EBSD-based trace analysis

Tensile behavior and deformation mechanism for Ti–22Al–25Nb alloy with lamellar O microstructures

In situ EBSD study of formation and propagation of deformation bands in a single-crystal superalloy during tensile deformation

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy

In-Situ SEM Study on Deformation and Failure Mechanism of TC4 Titanium Alloy by Laser Additive Manufacturing

Study on the dynamic deformation behavior and microstructure evolution of Ti-5Al-2.5Sn utilized Quasi-In-Situ method

An Investigation of Slip and Twinning Behavior of a Zirconium Alloy During Plastic Deformation Based on In-Situ SEM-EBSD

An investigation of the tensile deformation mechanism of a high-oxygen Ti2448 alloy fabricated by powder metallurgy by use of the in-situ EBSD method

Study of Deformation Mechanisms of a High-Purity α-Titanium Plate Under Monotonic Loading with the EVPSC-TDT Model