Abstract:Introduction. Modern conditions of iron and steel making industry require production of high-quality competitive metal products. Thus, the removal of sulfur at the lowest cost has been becoming increasingly important.Problem Statement. The major amount of sulfur in iron and steel making comes with charge materials in sintering blast furnace production. When using out-of-furnace processing of hot metal in hot metal desulfurizationand slag removal facilities, the degree of hot metal desulfurization can be 75—99%. This ensures the production of hot metal with a sulfur content in the range of 0.002—0.015%.Purpose. The analysis of changes in the sulfur content of hot metal and in the slag composition in the processchain of steel production, followed by the development of technical solutions and process methods to eliminate theresulfurization of hot metal.Materials and Methods. Our calculations, based on the actual data of Ukrainian and Chinese iron and steelmaking facilities. The selected samples of slag and hot metal have been analyzed with the use of raster spectralmicroscopy methods. In the studies of sulfur content at various stages of smelting, the method of material balancecalculation has been employed.Results. In the slag phase, along with systems of CaO ∙ SiO2 ∙ Al2O3 type with diff erent ratios of componentscontaining 0.2—3.5% sulfur, CaxSiyAlz type systems containing up to 1% sulfur have been detected. In the beads, the sulfur content varies within 0.1—0.85%. Sulfur is present in the form of sulfi des of (Fe, Mn)S type, mainlyMnS, while in non-metallic inclusions of the beads, the sulfur content ranges within 15—30%. The residing ladleslag after desulfurization should not exceed 0.5—0.7 kg/t of hot metal.Conclusions. To prevent the resulfurization of hot metal during its discharge from a blast furnace, it is advisable to rationalize ladle slag modes, by adjusting ladle slag composition, increasing the degree of ladle cleaning from the slag residing from previous loads and inducing a slag cover in the absence of ladle slag. The conducted studies have shown that sulfur from the slag does not return to the hot metal and resulfurization does not occur, which is explained by the protective eff ect of residual magnesium.

Control of Sulphur for Spring Steel Killed by Si–Mn and with Low Basicity Slag

Optimum Composition of Cao-Sio2-Al2o3-Mgo Slag for Spring Steel Deoxidized by Si and Mn in Production

Effect of Top Slag with Low Basicity on Transformation Control of Inclusions in Spring Steel Deoxidized by Si and Mn

Research of slagless steelmaking and technology control in converter

Study on the Cleanliness of SWRS82B Hard Wire Steel Refined by Fluorine‐Free Slag with Medium and High Basicity

Effect of low basicity refining slag on evolution and removal of oxide inclusions in 55SiCrA spring steel

Influence of Calcium Treatment on Cleanness and Fatigue Life of 60si2mna Spring Steel

Sulphur removal in ironmaking and oxygen steelmaking

Effect of CaO/Al2O3 Ratio in Fluorine‐Free Refining Slag with Low Basicity on the Cleanliness of SWRS82B Steel

Change in Slag Composition and Sulfur Content of Hot Metal in the Process Chain of Blast Furnace — Hot Metal Desul furization Complex — Converter (BOF)

Optimizing RH refining process to maximize cleanliness of low-carbon low-silicon Al killed steel

Simulation of Ladle Refining Reactions in Si–Mn‐Killed Steel

Control of Steel Composition and Evolution of Inclusions During Electroslag Remelting of NiCrMoV High‐Strength Steel

Mass Transfer Model of Desulfurization in the Electroslag Remelting Process

Experiments on effect of red mud-based slag on distribution of sulfur in liquid iron

Influence of Slag and Refractory Materials on Inclusions during the Ladle Refining of Low Carbon Aluminum Killed Steel

Elimination of Fluorspar Use and Reduction in Lime Consumption at Ladle Furnace by Reutilizing Alumina-Rich Ladle Furnace Slag

Dephosphorization of high silicon hot metal based on double slag converter steelmaking technology

Effect of Refining Slag Composition on the Cleanliness of Oriented Silicon Steel

Control of oxide inclusion for low carbon and low silicon steel

Directional sulfur removal from ladle furnace slag by electric field strengthening treatment