Abstract:Introduction. Modern conditions of iron and steel making industry require production of high-quality competitive metal products. Thus, the removal of sulfur at the lowest cost has been becoming increasingly important.Problem Statement. The major amount of sulfur in iron and steel making comes with charge materials in sintering blast furnace production. When using out-of-furnace processing of hot metal in hot metal desulfurizationand slag removal facilities, the degree of hot metal desulfurization can be 75—99%. This ensures the production of hot metal with a sulfur content in the range of 0.002—0.015%.Purpose. The analysis of changes in the sulfur content of hot metal and in the slag composition in the processchain of steel production, followed by the development of technical solutions and process methods to eliminate theresulfurization of hot metal.Materials and Methods. Our calculations, based on the actual data of Ukrainian and Chinese iron and steelmaking facilities. The selected samples of slag and hot metal have been analyzed with the use of raster spectralmicroscopy methods. In the studies of sulfur content at various stages of smelting, the method of material balancecalculation has been employed.Results. In the slag phase, along with systems of CaO ∙ SiO2 ∙ Al2O3 type with diff erent ratios of componentscontaining 0.2—3.5% sulfur, CaxSiyAlz type systems containing up to 1% sulfur have been detected. In the beads, the sulfur content varies within 0.1—0.85%. Sulfur is present in the form of sulfi des of (Fe, Mn)S type, mainlyMnS, while in non-metallic inclusions of the beads, the sulfur content ranges within 15—30%. The residing ladleslag after desulfurization should not exceed 0.5—0.7 kg/t of hot metal.Conclusions. To prevent the resulfurization of hot metal during its discharge from a blast furnace, it is advisable to rationalize ladle slag modes, by adjusting ladle slag composition, increasing the degree of ladle cleaning from the slag residing from previous loads and inducing a slag cover in the absence of ladle slag. The conducted studies have shown that sulfur from the slag does not return to the hot metal and resulfurization does not occur, which is explained by the protective eff ect of residual magnesium.

Dephosphorization of high silicon hot metal based on double slag converter steelmaking technology

Effect of Temperature on Dephosphorization of Hot Metal in Double‐Slag Converter Steelmaking Process by High‐Temperature Laboratorial Experiments

Effect of highly oxidizing converter dephosphorization slag on dephosphorization behaviour of molten steel

Kinetics of Dephosphorization at Different Slag Basicities in the Double Slag Converter Steelmaking Process

Dephosphorization in New Double Slag Converter Steelmaking Process with High‐Temperature Laboratorial Experiments

Study on Efficient Dephosphorization in Converter Based on Thermodynamic Calculation

Factors Influencing Dephosphorization of Low Carbon Steel in Converter

Research of slagless steelmaking and technology control in converter

Behavior of Carbothermal Dephosphorization of Phosphorus-Containing Converter Slag and Its Resource Utilization

Influence of the Basicity on Phosphorus Enrichment Properties of Decarbonization Slag in Low‐Carbon Double Slag Converter Steelmaking Process with Industrial Experiments, Mineralogy, and Ion–molecule Coexistence Theory

Dephosphorization Kinetics of Hot Metal at Low Slag Basicity and Low Temperature under the Different Fe2O3 Addition Amounts

Development and prospects of molten steel deoxidation in steelmaking process

Effect of CaO-MgO-FeO-SiO2-xNa2O Slag System on Converter Dephosphorization

KEY FACTORS FOR THE SEPARATION OF SILICON AND IRON DURING PHOSPHORUS RECOVERY FROM SLAG DISCHARGED FROM THE DOUBLE-SLAG REFINING PROCESS

Leaching behavior and microstructure of phosphorus in converter slag

New steelmaking process based on clean deoxidation technology

Change in Slag Composition and Sulfur Content of Hot Metal in the Process Chain of Blast Furnace — Hot Metal Desul furization Complex — Converter (BOF)

Study on oxygen blowing optimisation of reducing (FeO) content in slag in EAF steelmaking process with high ratio of hot metal to scrap

Control of oxide inclusion for low carbon and low silicon steel

The Direct Alloying of Steel through Silicothermic Self-Reduction of Chromite Ore Utilizing Si-Containing Solid Waste

A Kinetic Study on Selective Leaching of Phosphorus from Dephosphorization Slag