Abstract:Steel slags are solid residual materials formed as by-products throughout the process of steel production within the steelmaking industry. These wastes have good physical properties such as high stiffness and friction angle for use as road fill materials or in geotechnical applications. However, the presence of heavy metals and high alkalinity levels constitute significant environmental hazards and set limitations on using slags in engineering applications. While there have been investigations into the mechanical characteristics of steel slags, research on assessing potential harm when utilizing the materials in engineering applications is rare. This study examines the mitigation methods to address the environmental problems associated with steel slags. To do this, two different steel slags with different production techniques were treated with soils of different properties such as fine and coarse sand, bentonite, kaolin, and natural clay. The pH and electrical conductivity (EC) values of pure steel slags were determined using the water leach test (WLT). Variations in pH and EC values of steel slags subjected to treatment were evaluated through both WLT and sequential water leach (SWLT) tests. As a result, the high strength, stiffness, and drainage capability of EAF and LS steel slags make these materials suitable for road filling. This is further backed by their soaked and unsoaked CBR values. During the water leach tests, notable decreases in pH were observed with a 60% natural clay (NC) solution, resulting in a decrease of 1.2 and 0.7 in EAF and LS, respectively. The addition of sand had a negligible impact on pH due to its inert characteristics. Moreover, in sequential water leach tests, the most significant decrease in pH was observed with NC (with a reduction of 2.0 points for EAF and 0.9 points for LS) through enhanced ion exchange and extended periods of dilution and buffering. Also, the use of NC resulted in substantial decreases in EC for EAF and LS, with reductions of 77% and 81%, respectively. Moreover, heavy metal concentrations in leachate waters from pure steel slags have been detected, and the effect of treatment on aluminum and iron concentrations has been determined. The results indicate that the use of natural soil significantly drops the pH and lowers the trace metal concentrations within the leachate.

Directional sulfur removal from ladle furnace slag by electric field strengthening treatment

Mass Transfer Model of Desulfurization in the Electroslag Remelting Process

Effects of CaO Content and Magnesium Additive in Electroslag on Desulfurization of Rejected Electrolytic Manganese Metal Scrap

Desulfurization of Rejected Electrolytic Manganese Metal by Electroslag Remelting Furnace with a Water-Cooled Electrode

Investigation on Desulfurization of Rejected Electrolytic Manganese Metal Scrap: Experiment and Mathematical Modeling

Effect of unmelted lime on the element distribution behavior on a CaO-SiO2-MgO-Al2O3-FeO-CaF2(-Cr2O3) slag

Generation, utilization, and environmental impact of ladle furnace slag: A minor review

Experiments on effect of red mud-based slag on distribution of sulfur in liquid iron

An unconventional approach for the efficient recovery of iron, cobalt, copper and silicon from copper slag

In-Line Co-Processing of Stainless Steel Pickling Sludge Using Argon Oxygen Decarburization Slag Bath: Behavior and Mechanism

Ultrasonic-enhanced selective arsenic removal and sulfide conversion from iron slag

Novel method for improving iron recovery from electric arc furnace slag: on-site hot modification

Removal of Residual Element Antimony from Molten Steel by CaC2-Containing Refining Slag

Immobilization of Chromium in Stainless Steel Slag Using Low Zinc Electric Arc Furnace Dusts

Effects of Slag Composition and Additive Type on Desulfurization of Rejected Electrolytic Manganese Metal Scrap by Na2O-containing Electroslag

An efficient method of preparing Si-Fe-Al-Ca alloy from coal gasification fine slag via plasma smelting and alternating current magnetic field

Effect of electrical parameters and slag system on macrostructure of electroslag ingot

Thermodynamic Phase Conversion Mechanism on Copper–Cobalt Slag Cleaning Process Using Gypsum Wastes as Sulfurizing Agent

Design and Construction of a Laboratory-Scale Direct-Current Electric Arc Furnace for Metallurgical and High-Titanium Slag Smelting Studies

Utilization of Natural Soils as a Remediation Method for Electric Arc Furnace and Ladle Slags

Simulation and Experimental Study on the Desulfurization for Smelter Off-Gas Using a Recycling Ca-based Desulfurizer