Abstract:Experimental and theoretical studies have been carried out to investigate the effects of the slag on desulfurization during the electroslag remelting (ESR) process with a focus of developing a mass transfer model to understand the mechanism of desulfurization. Stainless steel 1Cr21Ni5Ti was used as the electrode and remelted with two different kinds of slags using a 50-kg ESR furnace. The contents of sulfur along the axial direction of product ingots were analyzed. It was found that the sulfur content of 350 ppm in the electrode is reduced to 71 to 95 ppm in the ingot by remelting with the slag containing 5 wt pct of CaO, and lowered more to 47 to 59 ppm with another slag having 20 wt pct CaO. On the basis of the penetration and film theories, the theoretical model developed in this work well elucidates the kinetics of desulfurization revealing the mechanism of sulfur transfer during the ESR process. The calculation results obtained from the model agree well with the experimental results. The model indicates that when sulfur content in electrode is given, there is a corresponding minimum value of sulfur content in the ingot due to the kinetics limit. This lowest sulfur content cannot be further reduced even with increasing LS (sulfur distribution coefficient between metal and slag phases) or decreasing sulfur content in the slag. Constant addition of extra amount of CaO to the molten slag with the increase of sulfur content in the slag during the remelting process can improve the macrosegregation of sulfur distributed along the axial direction of ESR ingots. Since the rate-determining steps of the sulfur mass transfer lie in the metal phase, adding calcium as deoxidizer can change mass transfer of sulfur and thus promote desulfurization further during the ESR process.

Simulation and Experimental Study on the Desulfurization for Smelter Off-Gas Using a Recycling Ca-based Desulfurizer

Study and optimization of catalytic oxidation technology in spent caustic desulfurization

Improved removal of selenium by calcite-derived CaO with porosity and anti-sintering in presence of acid gas

A Study of High Temperature Desulfurization and Regeneration Using Iron-Calcium Oxides in a Fixed-Bed Reactor

Resource utilization of semi-dry flue gas desulfurization ash by thermal treatment on sintering machine

Study on thermal regeneration of saturated activated coke coupled with SO2 carbothermal reduction to produce elemental sulfur

Experimental Study on the Preparation of Desulfurizer for Low Temperature Dry Desulfurization by Digesting CaO in Urea Solution

Experiment and Mechanism Analysis of Desulfurization with a MgO-Based Desulfurizer Fixed Bed Method

Mass Transfer Model of Desulfurization in the Electroslag Remelting Process

Experimental Study on SO2 Recovery Using a Sodium–zinc Sorbent Based Flue Gas Desulfurization Technology

Sulfur Removal at High Temperature During Coal Combustion in Furnaces: A Review

Advances on resource utilization of semi-dry desulfurization ash by thermal decomposition: a high-efficiency and low-temperature method for large-scale processing

Preparation and performance of sludge-based desulfurizer by calcification

Fixing sulfur dioxide by feeding calcine oxide into the rotary volatilization kiln in zinc smelting plant

Application of Ca-based adsorbents in fixed-bed dry flue gas desulfurization (FGD): a critical review

Removal of H 2 S from simulated blast furnace gas by adsorption over metal-modified 13X zeolite

Two-step hot coal gas desulphurization process integrated with direct production of elemental sulfur using iron-based sorbents: A preliminary study

Thermal modification of copper slag via phase transformation for simultaneous removal of SO2 and NOx from acid-making tail gas

Process compatible desulfurization of NSP cement production: A novel strategy for efficient capture of trace SO 2 and the industrial trial

Novel Dry-Desulfurization Process Using Ca(OH)2/Fly Ash Sorbent in a Circulating Fluidized Bed

Preparation of calcium sulfate from recycled red gypsum to neutralize acidic wastewater and application of high silica residue