Abstract:SO3 in coal-fired flue gas will cause equipment corrosion and the emission of sulfuric acid mist. The performance of injecting the alkaline adsorbent into the flue gas to remove SO3 is affected by the adsorption of SO2 in the flue gas. Taking Ca(OH)(2) as a typical alkaline adsorbent, a model describing the adsorption of SO3 and SO2 by Ca(OH)(2) particles was established, based on the combination of the product island-growth model and the grain model. The parameters in the model were determined by the experimental data of adsorption in the fixed-bed reactor. The adsorption process of a single Ca(OH)(2) particle was studied by numerical simulation. The adsorption of SO3 and SO2 was found to involve two stages: (1) In the early stage when there existed unreacted grain surface in the particle, SO3 and SO2 mainly reacted with the left fresh grain surface. The SO3 adsorption was controlled by internal pore diffusion and surface reaction, in which internal pore diffusion played a major role. The SO3 adsorption showed a shrinking core mode. The SO2 adsorption was controlled by internal pore diffusion and surface reaction and occurred throughout the entire particle. The SO3 adsorption selectivity at the outer surface of the particle was the highest, and decreased with a decreasing dimensionless particle radius R/R-0. (2) In the later stage when the grain surface was completely reacted, the SO3 adsorption was controlled by internal pore diffusion and product-layer diffusion, in which product-layer diffusion played a major role. The SO2 adsorption was controlled by product-layer diffusion. The product-layer diffusion coefficient in the SO3 adsorption process was significantly higher than that of the SO2 adsorption, so SO3 was still significantly adsorbed in the later stage. The adsorption process of Ca(OH)(2) under different particle structure parameters showed that decreasing the particle radius and increasing the particle porosity and specific surface area increased the SO3 removal efficiency as well as the total conversion of Ca(OH)(2). Decreasing the particle radius and the specific surface area and increasing the particle porosity increased the SO3 adsorption selectivity by Ca(OH)(2). When preparing industrial adsorbents, the optimization of the particle porous structure should be given attention. (C) 2021 Elsevier Ltd. All rights reserved.

Improved removal of selenium by calcite-derived CaO with porosity and anti-sintering in presence of acid gas

Simultaneous Removal of SO2 and Trace SeO2 from Flue Gas: Effect of SO2 on Selenium Capture and Kinetics Study

Experimental study on simultaneous removal of sulfur and trace selenium element

Research on Vapor Mercury Adsorption by Ca-Based Sorbents

The effect of SO2 on CaO capture selenium in the flue gas: Density functional theory and experimental study

Effect of CO_2 on Trace Selenium Adsorption by CaO from Flue Gas

Insight into the role of SO 2 on selenium conversion during adsorption by CaO: Theoretical calculation and experimental study

CO2 Adsorption by Polyamine-Based Protic Ionic Liquid-Functionalized Mesoporous Silica: Regenerability and Influence of Flue Gas Contaminants

Simulation and Experimental Study on the Desulfurization for Smelter Off-Gas Using a Recycling Ca-based Desulfurizer

Capture of arsenic in coal combustion flue gas at high temperature in the presence of CaSiO3 with good anti-sintering

Simultaneous Removal of SO2 and Trace SeO2 from Flue Gas: Effect of Product Layer on Mass Transfer.

Feasibility Study on Simultaneous Removal of Sulfur and Trace Selenium in the MTD-FGD Reactor

Stable and Efficient As2O3 Removal from Simulated Flue Gas Using Al2O3/CaSiO3 Prepared by Anhydrous Grinding and Calcination Method

Simultaneous Removal of SO<sub>2</sub>and Trace SeO<sub>2</sub>from Flue Gas: Effect of Product Layer on Mass Transfer

Experimental and Density Functional Theory Study of the Adsorption Characteristics of CaO for SeO 2 in Simulated Flue Gas and the Effect of CO 2

SO 3 removal by submicron absorbents synthesized via inhibition method: The product layer grows like parallel peaks

Gaseous selenium removal by metal oxide sorbent: Experimental and density functional theory study

Experimental and Density Functional Theory Study of the Adsorption Characteristics of CaO for SeO2 in Simulated Flue Gas and the Effect of CO2

Chemically bonded zirconium oxide into CaO-based high-temperature coal-fired flue gas As 2 O 3 absorbents for enhanced anti-sintering properties: Experimental and DFT study

Process Analysis of SO3 Removal by Ca(OH)2 Particles from Flue Gas

Synthesis and Performance of a Nano Synthetic Ca-based Sorbent for High Temperature CO2 Capture