Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

A Static Nonlinear Analysis of Confined Brickmasonry Walls in a Multistory Building with a Large-Bay

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Experimental study and numerical simulation of seismic performance of stiffened thin steel plate shear walls considering the effect of vertical load on frame column

Experimental Study on Lateral Resistance Behavior of Small Concrete Hollow Block Wall with Different Constructional Measures

Analytical modeling of masonry load-bearing walls

Influence of constructional measurements on cracking of wall with small concrete hollow blocks

Seismic behavior of multi-story structural walls under cyclic lateral loading: Experimental study

Experimental Study on the Seismic Performance of Brick Walls Strengthened by Small-Spaced Reinforced-Concrete–Masonry Composite Columns

Experimental Study on Low Strength Brick Masonry Wall Strengthened with Self-compacting Concrete Wall

Behavior of Axially Compressed Concrete-Reinforced Sandwich Wallboard

Nonlinear finite element analysis of prefabricated hollow-core reinforced concrete shear walls

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

State-of-the-art Development on ‘code for Design of Masonry Structures’

Analysis and Application of Double Steel Plate Concrete Composite Shear Wall in the R&D Building of Zhanjiang Bay Laboratory

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Comparative Analysis of Load Capacity on Three Kinds T-Shaped Short-Leg Shear Walls

Experimental Study on Seismic Behavior of Brick Walls Strengthened with Embedded Bars

Analysis of an example of old masonry residence strengthenedby external prefabricated reinforced concrete shear walls

Coupled Axial Tension-Shear Behavior of Reinforced Concrete Walls

Nonlinear FEM analysis of autoclaved aerated concrete block composite masonry walls

Experimental and Numerical Study on the Seismic Performance of Prefabricated Reinforced Masonry Shear Walls