Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Experimental Study on Low Strength Brick Masonry Wall Strengthened with Self-compacting Concrete Wall

Experimental Study of Masonry Walls Strengthened with Cfrp

Shake table test on a five-story residential masonry building strengthened by engineered cementitious composites based on minimum disturbance

Theoretical analysis and shaking table tests of old masonry structure reinforced by external frames with added stories on the top using seismic isolation technology

MECHANICAL BEHAVIOR OF MASONRY WALLS STRENGTHENED WITH CFRP

Shaking table test of fabricated concrete shear wall structure and study on damage mechanism of strong earthquake

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Experimental Study on the Seismic Performance of Brick Walls Strengthened by Small-Spaced Reinforced-Concrete–Masonry Composite Columns

Experimental Study on Both Sides Strengthening of Low-reinforced Shear Wall

Experimental Study on Seismic Behavior of Brick Walls Strengthened with Embedded Bars

Experimental study on the seismic performance of masonry wall reinforced by cement mortar and polypropylene band

Analysis of an example of old masonry residence strengthenedby external prefabricated reinforced concrete shear walls

Earthquake resistant behavior on seismic strengthening of typical rural brick-wood structure in Beijing

Combined Strengthening Techniques to Improve the Out-of-Plane Performance of Masonry Walls

EXPERIMENTAL STUDY OF A MASONRY BUILDING RETROFITTED INTEGRALLY BY PRE-FABRICATED RC PANELS

Influence of Confining Element Stiffness on the In-Plane Seismic Performance of Confined Masonry Walls

In-Plane Shear Strengthening of Masonry Wallettes Using Ultra-High Performance Concrete Precast Plates

Seismic Performance of the Pre-Fabricated Steel Frame Infilled with AAC Wall Panels and Their Joint Connection: Full-Scale Shaking Table Test

Experimental In-Plane Shear Performance of Masonry Infill Walls Assembled with Cementitious Matrix–Grid Composites