Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Analytical modeling of masonry load-bearing walls

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Macro-Modeling of Reinforced Concrete Structural Walls: State-of-the-Art

Finite element-based reliability analysis of reinforced concrete masonry walls under eccentric axial loading considering slenderness effects

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Elasto-Plastic Analysis Of Reinforced Concrete Shear Wall With Openings Using A Macro Model

Analysis on Reinforce Concrete Sandwich Wall-Panel Using Nonlinear Finite Element Method

Simplified mechanical models for the seismic collapse performance prediction of unreinforced masonry structures

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method

A Static Nonlinear Analysis of Confined Brickmasonry Walls in a Multistory Building with a Large-Bay

An improved method for statistics estimation of out-of-plane load resistance of masonry walls using design-code models and mechanics-based finite element models

Simplified homogenization technique for nonlinear finite element analysis of in-plane loaded masonry walls

Simulation of Masonry Wall using Concrete Damage Plasticity Model

An Orthotropic Elastic-Plastic Constitutive Model for Masonry Walls

A block-based numerical strategy for modeling the dynamic out-of-plane behavior of unreinforced brick masonry walls

Experimental Study of Masonry Walls Strengthened with Cfrp

MECHANICAL BEHAVIOR OF MASONRY WALLS STRENGTHENED WITH CFRP

Improving In-Plane Behavior of Weak Brick Masonry Walls Through Assimilation of Partially Confining RC Bands

3D hybrid modelling approach combining the finite and discrete element methods: Validation based on masonry shear wall tests

Nonlinear finite element analysis of prefabricated hollow-core reinforced concrete shear walls

Numerical and Experimental Investigation on Cyclic Behavior of Masonry Infill Walls Retrofitted with CFRP