Abstract:TiAl based alloys have been widely used as promising aerospace structural materials, which benefit from their unique combination of mechanical properties. However, they yield poor plasticity and low process ability, thus restricting the wide application. In this work, an efficient way was proposed by which direct current (DC) was imposed on the solidification process of TiAl-based alloy. Influences of DC on the microstructure and properties of directionally solidified Ti-48Al-2Cr-2Nb alloy using water cold crucible directional solidification equipment has been investigated. The changes of solidification microstructure, phase structure and composition of the alloy and gamma/alpha(2) interlamellar structures were characterized by OM, XRD, SEM and TEM. The effect of DC on the size of eutectoid colony, interlamellar spacing and relative content of a 2 phase had been studied by Image Pro Plus. Furthermore, the mechanical properties of the directionally solidified Ti-48Al-2Cr-2Nb alloy at 800. were performed. The results revealed that the DC can evidently promote the homogeneity of the solidification component and refiner the structure, and the segregation in lamellar colonies can be efficiently reduced or eliminated to a certain extent. With the increasing of the current density, the grain size and lamellar spacing decreased first and then increased, however, the a 2 phase content showed a totally different trend. Moreover, the microhardness, compression yield strength and the fracture strength of the alloy also revealed a trend of decrease after the first increase too. With the current density increasing, the average grain size and interlamellar spacing declined to the lowest of 0.46 mm and 0.19 mu m, respectively, and the content of a 2 phase increased from 18.5% to 39.4%. The microhardness of sample reached 542 HV, the compression yield strength and the fracture strength were remarkably improved, and the maximum values reached 1200 and 1365 MPa, respectively. DC can cause a reduction of the supercooling in front of the liquid phase during the solidification process. The results can be seen as the peritectic reaction L ->beta+L -> a+beta moving a tiny drift to the direction of the Al-rich side in TiAl binary phase diagram, consequently, the primary beta-phase increased, and the content of alpha(2) phase, microstructure under room temperature, increased evidently.

Effect of Medium-Density Direct Current on Dendrites of Directionally Solidified Pb–50Sn Alloy

Effect of Directional Solidification Methods on Solid Solution Window in Ni-based Single-Crystal Superalloy

Influence of Electric Current on Directional Solidification Structure of Al-4.5%Cu Alloy

Effect of an Axial High Magnetic Field on Sn Dendrite Morphology of Pb–Sn Alloys During Directional Solidification

Effect of a Transverse Magnetic Field on Solidification Structure in Directionally Solidified Sn–Pb Hypoeutectic Alloys

Influence of a direct current on the solidification behavior of pure aluminum

Effect of electromagnetic stirring current on the mechanical properties of Cu-15Ni-8Sn alloy and its mechanism of inducing dendrite refinement and Sn distribution homogenization

Effects of Direct Current on Microstructure and Properties of Ti-48Al-2Cr-2Nb Alloy

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

Effect of Direct Current on Solid-Liquid Interfacial Tension and Wetting Behavior of Ga–In–Sn Alloy Melt on Cu Substrate

Effect Of Pulling Velocity On Dendrite Arm Spacing In Steady-State Directionally Solidified Transparent Organic Alloy By Numerical Simulation

The Effect of Low Cooling Rates on Dendrite Morphology During Directional Solidification in Mg–Gd Alloys: in Situ X-ray Radiographic Observation

In Situ Synchrotron X-ray Imaging on Morphological Evolution of Dendrites in Sn–Bi Hypoeutectic Alloy under Electric Currents

Thermal and Solute Diffusion During Dendrite Growth of Mg-5wt.%Zn Alloy

Effect of electric current on stability of solidification interface morphology

Evolution of dendrite morphology of a binary alloy under an applied electric current: an in situ observation

Influence of a Weak Static Magnetic Field on the Primary Dendrite Arm Spacing of a Directionally Solidified Ni-based Superalloy

Evolution of Dendrite Morphology of a Binary Alloy under an Applied Electric Current: Anin Situobservation

Effect of Melt Convection on Primary Dendrite Arm Spacing in Directionally Solidified Pb-26%Bi Hypo-Peritectic Alloys

Effect of Current Intensity on Microstructure of Ni3Al Intermetallics Prepared by Directional Solidification Electromagnetic Cold Crucible Technique

Dendrite Coarsening in Directionally Solidified Sn–36 At.%ni Peritectic Alloy in the Presence of the Migration of Secondary Dendrite Arms