Abstract:Emissivity is an important parameter to characterize the thermophysical properties of materials. For non-conductive materials, high-temperature furnace heating or radiant heating is generally used in emissivity measurement. The problem in high-temperature furnace heating method is that tested materials may chemically react with the material of the heating container, thereby destroying the original characteristics of the materials. There will be problems of non-uniform heating of samples in the radiant heating method. The tested materials are usually heated unidirectionally and still in the radiant heating method, so there will be samples non-uniform distribution of sample temperature gradient. Based on laser rotating heating and sample/black body integrated design, this paper proposes a new method. The samples are spinning while measuring, measuring the emissivity of non-conductive materials at high temperature, and establishing a corresponding measurement model. This method break through the limitations of traditional measurement methods, in which the samples are still while measuring. The sample and black body are designed integrally, and the micro-area spectral radiation imaging method is adopted to measure the spectral radiation energy and temperature of the black reference body and the sample at the same time. The heat conduction equation under the laser rotating heating state is established, and the temperature distribution of typical sample materials is simulated. The results show that the temperature field distribution of the rotating sample is relatively uniform. The relationship between the temperature field distribution and the infrared spectral emissivity measurement error is analyzed. The lower limit of the material thermal conductivity applicable to this test method is shown. Based on this method, a corresponding measurement device was built to test the spectral emissivity of a typical material silicon carbide at 1 000 K. The spectral emissivity of each specific high-temperature point was tested at 4 mu m, and the silicon carbide material was measured at The characteristics of the spectral emissivity wavelength change and temperature change rule characteristics of the infrared band. The results are compared with the foreign measurement results, and the results are relatively consistent, which verifies the feasibility of the laser rotating heating spectral emissivity test method. The characteristics of the spectral emissivity wavelength change and temperature change rule characteristics of the silicon carbide material in the infrared band are obtained. The results are compared with the foreign measurement results, and the results are relatively consistent, which verifies the feasibility of the laser rotating heating spectral emissivity test method. With this method, the physical and chemical characteristics of the sample are not destroyed, the sample heats up quickly, the temperature field in the measurement area is uniform, the upper limit of the measurement temperature range is high, and the temperature unevenness caused by the laser static and unidirectional heating is reduced effectively. The sample's temperature and spectral radiation energy can be measured at the same time, so the standard high temperature black body does not need to be designed separately. This method solves the existing high-temperature non-uniform heating and radiant energy synchronous comparison measurement in non-conductive materials emissivity measurement. It can be applied to measure the high-temperature spectral emissivity of various non-conductive materials.

70～580K小样品全自动精密绝热量热装置的建立——α-Al 2 O 3 的摩尔热容

A small sample-size automated adiabatic calorimeter from 70 to 580 K - Molar heat capacities of α-Al2O3

A small sample-size automated adiabatic calorimeter from 70 to 580 K

A Low-temperature Automated Adiabatic Calorimeter Heat Capacities of High-purity Graphite and Polystyrene

An Adiabatic Calorimeter for Heat Capacity Measurements of Small Samples - the Heat Capacity of Nonlinear Optical Materials Ktiopo4 and Rbtioaso4 Crystals

Experimental Investigation on the Thermal Performance of a Large-Size Aluminum Vapor Chamber for Multi-Point Heat Sources

Temperature Measuring System in High Temperature Carbon Reducing Environment

A Devices for Measuring Low Temperature of Filament in Ion Source of VG 354 Thermal Ionization Mass Spectrometer and Its Application

Design and Construction of a Guarded Hot Plate Apparatus Operating Down to Liquid Nitrogen Temperature.

Thermal Test Apparatus for Mini Heat Sinks

High Temperature Sensors Fabricated on Al2o3 Ceramic and Nickel-Based Superalloy Substrates

In Situ Integration of High-Temperature Thin-Film Sensor for Precise Measurement of Heat Flux and Temperature on Superalloy Substrate

Method and Device for Measuring High-Temperature Spectral Emissivity of Non-Conductive Materials Based on Laser Rotation Heating

Development of Simple Temperature Heating Station of D8 X-ray Diffractometer

Experimental Investigation of High Temperature Thermal Contact Resistance of Thin Disk Samples Using Infrared Camera in Vacuum Condition

Thermal Conductivity Measurement System for Functional and Structural Products

Study the Al2O3 Nano-Fillers Performances of Metallic Hollow Microlattice Material As a Heat Insulation on the High-Temperature

Development of thermal vacuum cryo-trap experimental apparatus

Automated Instrumentation for High-Temperature Seebeck Coefficient Measurements

Precise Determination of the Thermal Conductivity of the Thermal Insulating Metal Material

Study Of An Alum-Ceramic Heat Storage Material