Abstract:Large volume cubic press is one of the most popular high pressure devices which can produce pressures up to about 7 GPa. It is well known experimentally that the enhancing of the maximum pressure generated in the large volume cubic press has attracted wide attention among scientists and engineers because the higher pressure is capable of synthesizing some materials with interesting properties. In the large volume cubic press, pyrophyllite is typically used as a pressure-transmitting medium. A specimen immersed in such a solid experiences a generalized stress state. The pressure distribution in pyrophyllite is an important parameter for characterizing the sample environment and designing the experiments at high pressure. There is a need for the quantitative measurement of pressure gradients in the pyrophyllite pressure medium, so that the accurate experimental data under high pressure can be obtained. In the large volume cubic apparatus (68 MN), we put a circuit into the high pressure cubic cell, so that the pressures at various positions can be measured by using the phase transitions in Bi, Tl and Ba. In the present work, the relationship between the total press load and the press load allocated to the anvil face, and the relationship between the total press load and the press load allocated to gaskets are established at room temperature. The results show that with the increase of the total press load, the load allocated to the gaskets is increased sharply, while the curve of load allocated to the anvil face versus total press load reaches a plateau, which results in the cell pressure reaching upper limit when the cell pressure reaches up to about 5 GPa. According to the experimental results, the stress state of the cubic cell under high pressure is analyzed and the reason why the pressure generated in the large volume cubic chamber is difficult to exceed 7 GPa is explained. Based on the geometrical structure of the cubic cell, the scheme to increase the upper pressure limit for cubic cell by using the material with high bulk modulus as the pressure transmitting medium and the material with low bulk modulus as the gasket, is proposed. Additionally, the method of calculating the pressure values at different positions along the axis of symmetry in the cubic cell is given through the quantitative calibration of the pressure gradient in the axial direction of the cubic cell. This method can provide more accurate pressure data for high pressure experiments.

A Nearly Zero Temperature Gradient Furnace System for High Pressure Multi-Anvil Experiments

A Rapid-Quench Technique for Multi-Anvil High-Pressure-temperature Experiments.

Small furnace for the small angle X-ray scattering (SAXS) and wide angle X-ray scattering (WAXS) characterization of the high temperature carbonization of coal

EXPERIMENTAL STUDY ON THE PHASE RELATIONS OF THE SYSTEM Mg2SiO4-MgAl2O4 AT HIGH PRESSURE AND HIGH TEMPERATURE

A Simplified Rapid-Quench Multi-Anvil Technique.

A Furnace to 1200 K for in Situ Heating X-Ray Diffraction, Small Angle X-Ray Scattering, and X-Ray Absorption Fine Structure Experiments

A novel method for experiments in a one-atmosphere box furnace

Quantitative Measurements of Pressure Gradients for the Pyrophyllite and Magnesium Oxide Pressure-Transmitting Mediums to 8 Gpa in A Large-Volume Cubic Cell

Force Analysis and Pressure Quantitative Measurement for the High Pressure Cubic Cell

Technical Development of the Multi-Anvil High-Pressure-Temperature Apparatus and its Application to Study of the Earth's Interior

Furnace for Inelastic X-Ray Scattering from Liquids to 1600C

Development of a microfurnace dedicated to in situ scanning electron microscope observation up to 1300 °C. II. Study of the thermal response of samples

High-temperature furnace for in situ GISAXS studies

A novel rapid cooling assembly design in a high-pressure cubic press apparatus

Raman Spectra Based Pressure Calibration of the Non-Gauge Sapphire Anvil Cell at High Temperature and High Pressure

Isothermal furnace for long-term in situ and real-time X-radiography solidification experiments

Sample heating above 1400 K in a diamond anvil cell

A High P–T Cell Assembly for Neutron Diffraction Up to 10gpa and 1500 K

Laue microdiffraction on polycrystalline samples above 1500 K achieved with the QMAX‐μLaue furnace

Mirror Furnace for Synchrotron Dark Field X-ray Microscopy Experiments

Numerical analysis of thermohydraulic behavior in a directional solidification furnace