Abstract:In the ultra-large-scale integration (ULSI) technologies, polysilicon resistors are usually employed in the integrated circuits as a precise analog resistor element for a variety of applications, such as DAC (digital resistor give the solution of the linearity and Rs concerns to analog converter) in analogue circuits [1-3]. Conventionally the polysilicon resistance can be adjusted by ion implantation and post annealing process [4]. For the self-aligned implantation process, the dosage changes which are always utilized to adjust the resistance are feasible to induce the MOS characteristics changes, especially in the submicron process whose short-channel effects (SCE) are much more sensitive to the dosages [5]. In this work, we propose a new inner anneal process in N2ambient after polysilicon re-oxidation to reduce the polysilicon resistance by changing the polysilicon grain size. The test patterns are manufactured on 300mm-diameter wafer by 65-nm 1-poly 7-metal standard CMOS technology. After polysilicon re-oxidation to form oxide film on polysilicon surface, the wafers are annealed at 800oC, 900oC, 950oC and 1000oC in N2ambient, respectively. Fig. 1 shows the process flow and annealing process steps in the flow. After anneal, the polysilicon grain size is measured by X-ray powder diffraction (XRD). And the electric characteristics for NMOS, PMOS and polysilicon resistance are tested. Fig. 2 shows the poly resistance reduction proportion and poly grain size after anneal at 800oC, 900oC, and 1000oC for 5min, and 950oC for 20min in N2 ambient, respectively. Only after annealing at 950oC or above for 5min, the resistance can be obviously reduced, due to the poly grain size increasing. Fig. 3 shows threshold voltages (Vt) variation proportions of NMOS and PMOS owning gate length of 65nm and width 0.12µm after utilizing annealing process at different temperatures. PMOS is more sensitive to the anneal process than NMOS. But after anneal at 950oC or below, the threshold variation for both NMOS and PMOS is less than 5%, which is acceptable for the integration process manufacturing. A new anneal process at N2 ambient to adjust the polysilicon resistance has been proposed. It has been verified that utilizing anneal process at 950oC or below, the 65nm MOS performances can be maintained almost same as before. Consequently, it is considered that the anneal method can be to be applied to the deep submicron integration process. References [1] C. D. Parikh, and R. M. Patrikar, Solid-state Electronics, 43, 683 (1999). [2] R. Murii, and M. J. Deen,, IEEE Trans. Electron Devices, 49, 187 (2002). [3] C. Uang, H. Chuang, S. Tsai, K. Thei, P. Lai, S. Fu, Y. Tsai, W. Liu, IWJT, 293 (2004). [4] S. Gupta, J. Electrochem. Soc. 149, G271 (2002). [5] R. H. Dennard, F. J. Gasensslen, H. M. Yu, V. L. Rideout, E. Bassous, A. R. Leblanc, Solid-state Circuits Soc Mag. IEEE, 87, 668 (1999). Figure 1

Performance Improvement by Cold Xe Pre-Amorphization Implant for Nickel Silicidation of 28-nm PMOSFET

Abnormal oxidation in nickel silicide and nickel germanosilicide in sub-micro CMOS

A comparative study of C, N and Xe pre-amorphization implantation processes for improving the thermal stability of NiSi films

Ni Silicide and Ni Germanosilicide Self-Aligned Process for 65nm and Beyond CMOS Technology by 2-Step Rapid Thermal Annealing

Simulation Study of Device Physics Issues in III&#x2013;V MOSFETs at 10 Nm Node

Design on Formation of Nickel Silicide by a Low‐Temperature Pulsed Laser Annealing Method to Reduce Contact Resistance for CMOS Inverter and 6T‐SRAM on a Wafer‐Scale Flexible Substrate

Improvement of Thermal Stability of Nickel Silicide Using Co-Sputtering of Ni and Ti on Boron Cluster Implanted Ultra-Shallow Junction for Nanoscale CMOS Technology

Performance Improvement by Blanket Boron Implant in the Sigma-Shaped Trench Before the Embedded SiGe Source/Drain Formation for 28-Nm PMOSFET

High-Performance Zno Nanowire Field-Effect Transistor With Forming Gas Treated Sio2 Gate Dielectrics

Field-Induced Crystalline-to-Amorphous Phase Transformation on the Si Nano-Apex and the Achieving of Highly Reliable Si Nano-Cathodes

Schottky barrier height tuning of silicides on p-type Si (100) by aluminum implantation and pulsed excimer laser anneal

A New Low-cost Technique for Mobility Enhancement of PMOSFETs Strained by Ge Pre-amorphization Implantation for Source/Drain Extension

Experimental Investigation of As Preamorphization Implant on Electrical Property of Ti-Based Silicide Contacts

Effects of sequential annealing in low oxygen partial-pressure and NO on 4H-SiC MOS devices

The Influence of Silicide Technique on the Device Performance for Deep Sub-Micro Pmosfets

Study on the Impact of Germanium Preamorphization on the Work Function of Fully Silicided NiSi Gate

Optimization of zero-level interlayer dielectric materials for gate-all-around silicon nanowire channel fabrication in a replacement metal gate process

The Leakage Current Improvement of a Ni-Silicided SiGe/Si Junction Using a Si Cap Layer and the PAI Technique

On Different Process Schemes for MOSFETs with a Controllable NiSi-Based Metallic Source/Drain

Performance Improvement of Planar Silicon Nanowire Field Effect Transistors Via Catalyst Atom Doping Control

Thermal Method to Reduce the Polysilicon Resistance for Deep Submicron Integration Process