Abstract:The coarse segregative eutectic phases, emerged in the twin roll casting (TRC) process of Mg strips, which cannot be resolved solely by controlling the processing variables or post heat treatment, are detrimental to the subsequent rolling deformation. Considering it, we introduce the pre-rolling steps on the TRC Mg-4Al-2Sn-1 Zn (ATZ421) alloys, which is expected to facilitate the dissolution of these segregative phases by increasing distortion of crystal lattices and rolling stress, and further investigate the effect of a single pass or two passes pre-rolling on the microstructure evolution and tensile properties. It indicates that the pre-rolled alloy with two passes presents more uniform precipitates and higher twinning density in comparison with that using a single pass. The uniform distribution of precipitates in two passes pre-rolling is due to the increase in density of dislocations and deformed twins, which results in more distortion of crystal lattices with more stored energy, facilitating the diffusion of solutes. Moreover, the pre-rolling of two passes introduces more rolling stress into Mg matrix, which is beneficial for the crush of coarse eutectic phases, and further accelerates the sufficient dissolution of second phases. After the subsequent rolling and annealing processes, the sheet with pre-rolling deformation of two passes shows finer microstructure, which mainly benefits from the pinning effects of uniform nano-sized precipitates. As a result, the annealed sheet with two-pass pre-rolling deformation exhibits an advantageous combination of high strength and high ductility with fine microstructure, showing an ultimate tensile strength of similar to 297 MPa, a yield strength of similar to 205 MPa and an elongation of 25.0%. This work provides an effective method of dissolving the coarse segregative phases in the TRC Mg alloys with significant potential for industrial production.

Improving the Mechanical Properties of a ZM61 Magnesium Alloy by Pre-Rolling and High Strain Rate Rolling

Enhancing the Mechanical Properties of High Strain Rate Rolled Mg–6Zn–1Mn Alloy by Pre-Rolling

Dynamic Precipitation, Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Sheets Prepared by High Strain-Rate Rolling

Microstructures evolution, texture characteristics and mechanical properties of Mg-2.5Nd-0.5Zn-0.5Zr alloy during the high strain rate hot-rolling

Microstructure Evolution and Mechanical Properties of the ZM61 Alloy Sheets under Different Pre-Rolling and High Strain Rate Rolling Temperatures

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Property Improvements in Fine–grained Mg–Zn–Zr Alloy Sheets Produced by Temperature–step–down Multi–pass Rolling

Deformation Induced Dynamic Recrystallization and Precipitation Strengthening in an Mg-Zn-Mn Alloy Processed by High Strain Rate Rolling

Development of the Fine-Grained Mg-0.6Zr Sheets with Enhanced Damping Capacity by High Strain Rate Rolling

Achieving single-pass high-reduction rolling and enhanced mechanical properties of AZ91 alloy by RD-ECAP pre-processing

Enhanced mechanical properties of AZ91 magnesium alloy by asynchronously large-strain high-efficiency rolling with bimodal grain structure

Microstructure and Tensile Properties of Rolled Mg-4Al-2Sn-1Zn Alloy with Pre-Rolling Deformation

Microstructure Evolution and Mechanical Properties of Mg-3al-3sn-1zn Alloy During Multi-Pass High-Speed Rolling

Microstructure and mechanical properties of Mg-Al-Zn alloys processed by different-speeds-rolling

Microstructure refining and property improvement of ZK60 magnesium alloy by hot rolling

Evolution of Microstructure and Mechanical Properties of ZK60 Magnesium Alloy Processed by Asymmetric Lowered-Temperature Rolling

Effect of Large Thickness-Reduction on Microstructure Evolution and Tensile Properties of Mg-9Al-1Zn Alloy Processed by Hard-Plate Rolling

Improving the mechanical properties of duplex Mg-Li-Zn alloy by mixed rolling processing

Achieving Fine Grain Structure and Superplasticity in AZ91-0.4Sn Magnesium Alloy Using Short Flow Rolling Process

Achieving enhanced mechanical properties in the Mg–Y–Zn–V alloy by refining grains and improving the morphology and distribution of LPSO via pre-forging and subsequent rolling

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet