Abstract:The industrial application of electrical discharge machining (EDM) for manufacturing injection molding, in many cases, requires forming depth cavities with high length-to-width ratios, which is quite challenging. During slot EDM with thin-walled electrodes, short-circuits and arcing discharges occur, as a result of low efficiency in removing debris and bubble gas from the gap. Furthermore, unstable discharges can cause increases in tool wear and shape deviation of the machined parts. In order to characterize the influence of the type of electrode material and EDM parameters on the deep slot machining of high-thermal-conductivity tool steel (HTCS), experimental studies were conducted. An analytical and experimental investigation is carried out on the influence of EDM parameters on discharge current and pulse-on-time on the tool wear (TW), surface roughness (Ra), slot width (S)-dimension of the cavity, and material removal rate (MRR). The analyses of the EDS spectrum of the electrode indicate the occurrence of the additional carbon layer on the electrode. Carbon deposition on the anode surface can provide an additional thermal barrier that reduces electrode wear in the case of the copper electrode but for graphite electrodes, uneven deposition of carbon on the electrode leads to unstable discharges and leads to increase tool wear. The response surface methodology (RSM) was used to build empirical models of the influence of the discharge current I and pulse-on-time ton on Ra, S, TW, and MRR. Analysis of variance (ANOVA) was used to establish the statistical significance parameters. The calculated contribution indicated that the discharge current had the most influence (over 70%) on the Ra, S, TW, and MRR, followed by the discharge time. Multicriteria optimization with Derringer's function was then used to minimize the surface roughness, slot width, and TW, while maximizing MRR. A validation test confirms that the maximal error between the predicted and obtained values did not exceed 7%.

Experimental Investigation on Carbon Steel Micro-Rod Machining by LS-WEDT

Analysis and Reduction of Process Energy Consumption and Thermal Deformation in a Micro-Structure Wire Electrode Electric Discharge Machining Thin-Wall Component

A study on wire electrochemical micromachining for fabrication of microgrooves

Investigation on a Novel Surface Microstructure Wire Electrode for Improving Machining Efficiency and Surface Quality in WEDM

Experimental investigation on the surface quality of WEDM machined 20MnCr5 steel for Gear application

Experimental investigation on WEDG machining parameters for tungsten carbide

Evaluation of Wire Electrical Discharge Machining Performance Features on EN AW-6082 T6 Aluminum Alloy and Optimization of Machining Characteristics

Experiments of Ti6Al4V manufactured by low-speed wire cut electrical discharge machining and electrical parameters optimization

Machining characteristics and optimization of 10CrNi3Mo alloy steel by WEDM

Experimental study on the influence of workpiece shape on discharge gap and burr in LS-WEDM and the preparation of microelectrode array with specific size

Research on Geometric Constraint Strategies for Controlling the Diameter of Micro−Shafts Manufactured via Wire Electric Discharge Grinding

Helical Surface Creation by Wire Electrical Discharge Machining for Micro Tools

Optimization of Wire Electric Discharge Machining (WEDM) Process Parameters for AISI 1045 Medium Carbon Steel Using Taguchi Design of Experiments

A Novel Strategy to Fabricate Thin 316L Stainless Steel Rods by Continuous Directed Energy Deposition in Z Direction

Improvement of the Machining Characteristics in WEDM Based on Specific Discharge Energy and Magnetic Field–assisted Method

Study on the Preparation Process for High Accuracy Micro Machining by Wire Electrical Discharge Machining

Optimization of Process Parameters on Surface Integrity in Wire Electrical Discharge Machining of Tungsten Tool YG15

Influence of different wire materials on the machining of Albromet W130 by WEDM

Investigating the influence of rotational speed in wire electric discharge machining of cylindrical workpieces: an experimental and simulation study

Wire Electrochemical Machining with Pulsating Radial Electrolyte Supply and Preparation of Its Tube Electrode with Micro-Holes

Experimental Investigation and Optimization of Rough EDM of High-Thermal-Conductivity Tool Steel with a Thin-Walled Electrode