Abstract:Titanium and its alloys (especially Ti6Al4V) are widely employed in aerospace and biomedical industry. Wire electric discharge machining is common in practice to machine this difficult-to-cut material. But owing to the thermo-electric nature of the process, it is challenging to have adequate level of surface integrity. This primary concern needs to be addressed as it mainly influences the surface mechanical characteristics. Therefore, the present research aims to address the aforesaid issues using well-known multipass strategy. Understanding the multipass process dynamics and requirements, the potentiality of brass wire diameters was comprehensively examined and explored during WEDM of Ti6Al4V. Considering higher cost, unavailability, environmental hazards, and straightness issues of novel zinc-coated wire electrodes, readily available brass wires provide a cheaper and widely acceptable solution to enhance surface integrity of machined parts if equivalent results can be somehow made possible. For that sake, three different brass wire diameters; 0.15 mm, 0.2 mm, and 0.25 mm have been considered to evaluate their impact on surface roughness, recast layer thickness, overcut, machined surface microhardness, and cutting speed using multipass cutting technique. Experimental results revealed that 0.15 mm uncoated brass wire can produce white layer result equivalent to Topas Plus X wire (Cu core-double Zn-rich layer coating) which outperformed among all zinc-coated wires used in previously published research. Moreover, among different diameter brass wires, surface roughness is improved by 25% using multipass cutting with 0.15 mm diameter in comparison to its counterparts. Scanning electron microscope (SEM) analysis depicts that the said combination reduces recast layer thickness from 39.04 μm to 14.6 μm (~ 1.5 times lesser value). In addition to that, smaller diameter (0.15 mm) provides the maximum cutting rate in rough cuts (which consume maximum machining time) and dimensional accuracy.

Influence of different wire materials on the machining of Albromet W130 by WEDM

The Machinability of Different Albromet W130 Plates Thicknesses by WEDM to the Required Surface Roughness Value

Evaluation of Wire Electrical Discharge Machining Performance Features on EN AW-6082 T6 Aluminum Alloy and Optimization of Machining Characteristics

Materials That Do Not Form Any Defects After WEDM

Experimental investigation of wire electrical discharge machining parameters on WE43 magnesium alloy

An in-depth evaluation of surface characteristics and key machining responses in WEDM of aerospace alloy under varying electric discharge environments

Machining Complex Profile on Nickel-Aluminum-Bronze Alloy through Wire Electric Discharge Machining Process using Zinc-Coated Brass Wire

Investigation on a Novel Surface Microstructure Wire Electrode for Improving Machining Efficiency and Surface Quality in WEDM

Rethinking wire electrical discharge machining: A case for engineering thick wires to enhance performance

Influence of Different Tool Electrode Materials on Electrochemical Discharge Machining Performances

Performance Studies on the Wire Electric Discharge Machining Characteristics of Stellite-6B Superalloys

Investigating the influence of rotational speed in wire electric discharge machining of cylindrical workpieces: an experimental and simulation study

Experimental Investigation on Wire Electric Discharge Machining of Biodegradable AZ91 Mg Alloy

Parametric investigation of W-EDM factors for machining AM60B conductive biomaterial

Analysis and Reduction of Process Energy Consumption and Thermal Deformation in a Micro-Structure Wire Electrode Electric Discharge Machining Thin-Wall Component

Characterization of cast rare earth WE43 magnesium alloy and parameter optimization for wire electrical discharge machining using TOPSIS & COPRAS

Synthesis and Characterization of Mechanical Properties and Wire Cut EDM Process Parameters Analysis in AZ61 Magnesium Alloy + B4C + SiC

Performance Analysis of Wire Electrodes on Machining Ti-6Al-4V Alloy using Electrical Discharge Machining Process

Investigation of the machining performance of Aluminum-Bronze alloy in WEDM using TAGUCHI method

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

Experimental Investigation and Optimization of Wire Electrical Discharge Machining for Surface Characteristics and Corrosion Rate of Biodegradable Mg Alloy