Abstract:Titanium and its alloys (especially Ti6Al4V) are widely employed in aerospace and biomedical industry. Wire electric discharge machining is common in practice to machine this difficult-to-cut material. But owing to the thermo-electric nature of the process, it is challenging to have adequate level of surface integrity. This primary concern needs to be addressed as it mainly influences the surface mechanical characteristics. Therefore, the present research aims to address the aforesaid issues using well-known multipass strategy. Understanding the multipass process dynamics and requirements, the potentiality of brass wire diameters was comprehensively examined and explored during WEDM of Ti6Al4V. Considering higher cost, unavailability, environmental hazards, and straightness issues of novel zinc-coated wire electrodes, readily available brass wires provide a cheaper and widely acceptable solution to enhance surface integrity of machined parts if equivalent results can be somehow made possible. For that sake, three different brass wire diameters; 0.15 mm, 0.2 mm, and 0.25 mm have been considered to evaluate their impact on surface roughness, recast layer thickness, overcut, machined surface microhardness, and cutting speed using multipass cutting technique. Experimental results revealed that 0.15 mm uncoated brass wire can produce white layer result equivalent to Topas Plus X wire (Cu core-double Zn-rich layer coating) which outperformed among all zinc-coated wires used in previously published research. Moreover, among different diameter brass wires, surface roughness is improved by 25% using multipass cutting with 0.15 mm diameter in comparison to its counterparts. Scanning electron microscope (SEM) analysis depicts that the said combination reduces recast layer thickness from 39.04 μm to 14.6 μm (~ 1.5 times lesser value). In addition to that, smaller diameter (0.15 mm) provides the maximum cutting rate in rough cuts (which consume maximum machining time) and dimensional accuracy.

Investigation on a Novel Surface Microstructure Wire Electrode for Improving Machining Efficiency and Surface Quality in WEDM

Sustainable Production of High-Uniformity Workpiece Surface Quality in Wire Electrical Discharge Machining by Fabricating Surface Microstructure on Wire Electrode

A New Wire Electrode for Improving the Machining Characteristics of High-Volume Fraction SiCp/Al Composite in WEDM

Analysis and Reduction of Process Energy Consumption and Thermal Deformation in a Micro-Structure Wire Electrode Electric Discharge Machining Thin-Wall Component

Improvement of the Machining Characteristics in WEDM Based on Specific Discharge Energy and Magnetic Field–assisted Method

Evaluation of Wire Electrical Discharge Machining Performance Features on EN AW-6082 T6 Aluminum Alloy and Optimization of Machining Characteristics

Study on surface evenness of super-high-thickness cutting in high-speed wire electrical discharge machining

Rethinking wire electrical discharge machining: A case for engineering thick wires to enhance performance

Wire electro-discharge grinding (WEDG) and its application

Optimization of Process Parameters on Surface Integrity in Wire Electrical Discharge Machining of Tungsten Tool YG15

Experimental Investigation and Optimization of Wire Electrical Discharge Machining for Surface Characteristics and Corrosion Rate of Biodegradable Mg Alloy

Study on Machining Characteristics of WEDM with Ultrasonic Vibration and Magnetic Field Assisted Techniques

Experimental Study On Wire Electric Discharge Machining Of Nimonic 90 Using Coated Electrode

Development and Experimental Study of MWEDM Prototype

Effect of Electrode Material and Hybrid Metaheuristic Optimization on Die Corner Accuracy during Wire Electrical Discharge Machining on Inconel (625): A Comparative Study

Complex Rotary Structures Machined By Micro-Wedm

Machining characteristics and optimization of 10CrNi3Mo alloy steel by WEDM

An in-depth evaluation of surface characteristics and key machining responses in WEDM of aerospace alloy under varying electric discharge environments

Experimental study of MWEDM technology

Study on the Preparation Process for High Accuracy Micro Machining by Wire Electrical Discharge Machining

Wire Electrochemical Machining with Pulsating Radial Electrolyte Supply and Preparation of Its Tube Electrode with Micro-Holes