Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate

Influence of grain structure and precipitates on fatigue crack propagation behaviors of Al- x Cu-1.2Li-X alloys

Influence of Grain Structure and Precipitates on Fatigue Crack Propagation Behaviors of Al-xCu-1.2Li-X Alloys

Effects of grain structures on fatigue crack propagation behavior of an Al-Cu-Li alloy

Fatigue crack propagation anisotropy of an Al–Zn–Mg–Cu super-thick plate

The Effect of Inhomogeneous Microstructures on Strength and Fatigue Properties of an Al-Cu-Li Thick Plate

On high‐cycle fatigue anisotropy of an aluminum alloy super‐thick plate

Study on Fatigue Crack Propagation and Extrinsic Toughening of an Al–Li Alloy

Goss Texture Intensity Effect on Fatigue Crack Propagation Resistance in an Al-Cu-Mg Alloy

A Crystallographic Model for the Orientation Dependence of Low Cyclic Fatigue Property of a Nickel-Base Single Crystal Superalloy

Fatigue crack propagation within Al-Cu-Mg single crystals based on crystal plasticity and XFEM combined with cohesive zone model

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate

Revealing the Effect of Oriented Microstructures on the Anisotropy of Fatigue Crack Propagation Behavior in TiB2/Al-Cu-Mg-Mn Composite

Investigation of High-Cycle Fatigue and Fatigue Crack Propagation Characteristic in 5083-O Aluminum Alloy

Texture Effect on Fatigue Crack Propagation Behavior in Annealed Sheets of an Al-Cu-Mg Alloy

In situ sem observation of self-arresting of fatigue cracks in Al-Li alloy 1420 thick plate

Fracture Toughness and Fatigue Behavior of T7451 Al-Zn-Mg-Cu Alloy Thick Plate

Microstructure sensitivity of the low cycle fatigue crack initiation mechanisms for the Al 0.3 CoCrFeNi high entropy alloy: in-situ SEM study and crystal plasticity simulation

Enhanced fatigue crack propagation resistance of a new Al–Cu–Li alloy via different aging processes

Texture and Tempered Condition Combined Effects on Fatigue Behavior in an Al-Cu-Li Alloy

Texture Effect on Fatigue Crack Propagation in Aluminium Alloys: an Overview