Abstract:Fatigue indicator parameters (FIPs) serve as the measurement of the driving force for fatigue crack initiation (FCI). The extreme value distributions of FIPs for fatigue life scatter (i.e., fatigue crack initiated from surface or subsurface) in the high cycle fatigue (HCF) to very high cycle fatigue (VHCF) regime are computed of AA7075-T6. The FIPs are averaged in the volume of sub-band in the scale of sub-grain proposed based on the concept of slip system of AA7075-T6 where sub-bands are extracted from statistical volume elements (SVEs) using open-source called Dream-3D. SVEs are built via the experimental crystalline microstructure. The material response variables required in the computation of FIPs are obtained by embedding crystal plasticity theory to the crystal plasticity finite element model via open-source software PRISMS-Fatigue. To meet statistical requirements, 50 instantiations of SVEs are modeled for both traction-free and fully periodic boundary conditions, respectively, corresponding to the surface and subsurface cases under different strain amplitudes (i.e., 0.362%, 0.312%, 0.289%, and 0.254%). It is found that the FIPs are higher under high stress levels indicating that fatigue crack tends to initiate at high stress levels. In addition, the low driving force can be found in the simulations with fully periodic boundary conditions throughout the SVEs, whereas the higher FIPs under traction-free boundary conditions tend to form close to the free surface under cyclic loading conditions. Furthermore, the highest FIPs have a propensity to scatter along with the depth of SVEs with the traction-free surface under strain amplitude of 0.254%, which means the fatigue life in the VHCF regime has a higher scatter. The interactions between the high symmetry of FCC crystalline structure and free surface combining the loading amplitudes have a compound effect on the FIPs, especially at low stress amplitudes, which also has a greater impact on the ultra-high-cycle fatigue life. To this end, the VHCF and HCF experiments are performed under an ultrasonic fatigue experimental system with a frequency of 20 kHz with different stress levels corresponding to the strain amplitude in the simulations. Besides, the morphology fracture surface of presentative samples was observed via the scanning electron microscope (SEM). The comparison between the simulation and the experimental results indicates that the EVD of FIPs is efficient in preciously predicting the FCI and well explain the fatigue life scatter of the AA7075-T6 in the HCF to VHCF regime.

Investigation of High-Cycle Fatigue and Fatigue Crack Propagation Characteristic in 5083-O Aluminum Alloy

Strain Ratio Effects on Low-Cycle Fatigue Behavior and Deformation Microstructure of 2124-T851 Aluminum Alloy

Investigation of fatigue crack propagation behavior of 5083 aluminum alloy under various stress ratios: Role of grain boundary and Schmid factor

High-Cycle Fatigue Behaviour of the Aluminium Alloy 5083-H111

On high‐cycle fatigue anisotropy of an aluminum alloy super‐thick plate

Investigation of the Fatigue Life Scatter for AA7075-T6 Using Crystal Plasticity Finite Element Method in the High to Very High Cycle Fatigue Regime

Comparison on the fatigue crack propagation of high‐strength aluminum alloys

Microstructure characterization and mechanism of fatigue crack propagation of 6082 aluminum alloy joints

Fatigue crack propagation anisotropy of an Al–Zn–Mg–Cu super-thick plate

Investigation on fatigue crack propagation behaviors in the thickness direction of 2519A aluminum alloy thick plate

Anisotropic Low Cycle Behavior of the Extruded 7075 Al Alloy

Mechanism of Precipitate Microstructure Affecting Fatigue Behavior of 7020 Aluminum Alloy

Explore the mechanism of high fatigue crack propagation rate in fine microstructure of friction stir welded aluminum alloy

The Microstructure and Fatigue Initiation of an AA2524-T34 Aluminum Alloy

Fatigue Behavior of Ultrafine-Grained 5052 Al Alloy Processed Through Different Rolling Methods

Investigation of the Combined Influence of Temperature and Humidity on Fatigue Crack Growth Rate in Al6082 Alloy in a Coastal Environment

Test Studies on Fatigue Performance of Aluminum Alloys Used in Construction

Damage Mechanisms and Anisotropy of an AA7010-T7452 Open-Die Forged Alloy: Fatigue Crack Propagation

Fatigue crack nucleation and microstructurally small crack growth mechanisms in high strength aluminum alloys

Microstructure sensitivity of the low cycle fatigue crack initiation mechanisms for the Al 0.3 CoCrFeNi high entropy alloy: in-situ SEM study and crystal plasticity simulation

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet