Abstract:The inhomogeneity of the microstructure of an Al-Cu-Li thick plate in the thickness direction results in inhomogeneity in the tensile property and fatigue crack propagation (FCP) rate. The grain size gradually increases from the surface layer to the central layer. The contents of low-angle grain boundaries (LAGBs) were characterized by an electron backscattered diffraction (EBSD) technique, and the LAGBs, which act as nucleation sites, induced a greater number of T-1 precipitates in the central layer. In the surface layer, the random texture resulted from the greater recrystallization degree due to the high degree of cold deformation during the rolling process. The 1/8 layer contained a rotated cube texture, which is a typical shear texture. A strong beta fiber rolling texture was found in the central layer, including S, brass and copper texture components, because the adequate recovery during hot rolling decreased the recrystallization driving force. Both the yield strength (YS) and ultimate tensile strength (UTS) gradually increased from the surface layer to the central layer, i.e., UTS from 479.7 MPa to 546.0 MPa, YS from 455.9 MPa to 514.0 MPa. The inhomogeneity of the tensile properties was primarily caused by the different textures, LAGB content and T-1 precipitate density. However, the surface layer had a distinctively lower FCP rate than the central layer. The disparity in the FCP rate between the surface layer and the central layer could be attributed to the roughness and plasticity, which are related to the LAGBs, the T-1 precipitates and the grain size.

Goss Texture Intensity Effect on Fatigue Crack Propagation Resistance in an Al-Cu-Mg Alloy

Texture Effect on Fatigue Crack Propagation Behavior in Annealed Sheets of an Al-Cu-Mg Alloy

P-Texture Effect on the Fatigue Crack Propagation Resistance in an Al-Cu-Mg Alloy Bearing a Small Amount of Silver

Texture Effect on Fatigue Crack Propagation in Aluminium Alloys: an Overview

Enhanced Fatigue Crack Propagation Resistance of Al-Cu-Mg Alloy by Intensifying Goss Texture and Refining Goss Grains

Texture Evolution and Its Effect on Fatigue Crack Propagation in Two 2000 Series Alloys

On the Role of Texture in Governing Fatigue Crack Propagation Behavior of 2524 Aluminum Alloy

Semi-quantitative Evaluation of Texture Components and Fatigue Properties in 2524 T3 Aluminum Alloy Sheets

Fatigue Crack Propagation of AA2024 Alloy under Texture Control Using Crystal Plasticity Coupled with Accelerated Cyclic Cohesive Zone Model

Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate

Enhanced Fracture Toughness in an Annealed Al-Cu-Mg Alloy by Increasing Goss/Brass Texture Ratio

Continuous Texture Evolution During Staged Solid Solution of Al‐Cu‐Mg and the Influence on Fatigue Resistance

Texture and Tempered Condition Combined Effects on Fatigue Behavior in an Al-Cu-Li Alloy

The Effect of Inhomogeneous Microstructures on Strength and Fatigue Properties of an Al-Cu-Li Thick Plate

Fatigue crack propagation within Al-Cu-Mg single crystals based on crystal plasticity and XFEM combined with cohesive zone model

Mechanisms for Goss-grains Induced Crack Deflection and Enhanced Fatigue Crack Propagation Resistance in Fatigue Stage II of an AA2524 Alloy

Influence of Grain Structure and Precipitates on Fatigue Crack Propagation Behaviors of Al-xCu-1.2Li-X Alloys

Influence of grain structure and precipitates on fatigue crack propagation behaviors of Al- x Cu-1.2Li-X alloys

Microstructure sensitivity of the low cycle fatigue crack initiation mechanisms for the Al 0.3 CoCrFeNi high entropy alloy: in-situ SEM study and crystal plasticity simulation

Effects of grain structures on fatigue crack propagation behavior of an Al-Cu-Li alloy

Fatigue Crack Propagation Across Grain Boundary of Al-Cu-Mg Bicrystal Based on Crystal Plasticity XFEM and Cohesive Zone Model