Abstract:The low-cycle fatigue of strongly-textured Mg alloys is dominated mainly by an alternation of twinning-detwinning process, which poses a great challenge to conventional constitutive models. As a result, a good reproduction of both mechanical response and deformation behavior often fails in previous simulations, in particular for high strain amplitudes. In the present study, the numerical simulations of low-cycle fatigue behavior of an Mg AZ31 plate with a ± 2% axial strain amplitude along the rolling direction were conducted, using a modified crystal-plasticity based on the finite strain elastic-viscoplastic self-consistent model containing twinning and detwinning mechanisms (EVPSC-TDT), and the results were compared with the mechanical response and deformation behavior determined by a real-time in-situ neutron diffraction. The simulations well predict the hysteresis loops and cyclic-hardening responses throughout the whole fatigue life (80 cycles), along with the evolution of the maximum twin volume fraction and residual twins. For the first time, the evolution of lattice strain throughout the whole fatigue life was calculated, and the results are in good accordance with that determined by neutron diffraction. The present study strongly demonstrates that the EVPSC-TDT model is very effective for modeling the low-cycle fatigue behavior of Mg alloys. More details about the evolution of the maximum twin volume fraction with fatigue cycles are found, an increase from 1st to 2nd cycle, followed by a decrease from 2nd to 20th cycle and a secondary increase after 20th cycle. This finding corrects the previous opinion that the maximum twin volume fraction increases at the initial stage and tends to be saturated at the late stage. Combining the results of simulations and neutron diffractions, the corresponding reasons are explained. Afterward, the mechanisms of the cyclic-hardening behavior at tension stage and compression stage are revisited, and some new insights are provided.

Fatigue Crack Propagation Across Grain Boundary of Al-Cu-Mg Bicrystal Based on Crystal Plasticity XFEM and Cohesive Zone Model

Fatigue crack propagation within Al-Cu-Mg single crystals based on crystal plasticity and XFEM combined with cohesive zone model

Fatigue Crack Propagation of AA2024 Alloy under Texture Control Using Crystal Plasticity Coupled with Accelerated Cyclic Cohesive Zone Model

An Insight into the Creep-Fatigue Damage Localization in Welded Joints Based on Crystal Plasticity Finite Element Method

Study on the crack nucleation mechanism of Ti-2Al-2.5Zr alloy in low cycle fatigue: Quasi in-situ experiments and crystal plasticity simulation

Crystal plasticity modeling of grain boundary softening and fatigue in U75V pearlite steel under low strain conditions: A study of cyclic rolling contact fatigue

Computational Boundary Layer Approaches for Fatigue Crack Propagation under Mixed‐mode Loading Conditions

Distinct Fatigue Cracking Modes of Grain Boundaries with Coplanar Slip Systems

Elastic-Plastic Simulation Study on 6005A Aluminum Alloy Crack Propagation Based on XFEM

Microstructure-informed, predictive crystal plasticity finite element model of fatigue-dwells

Understanding the Small Creep-Fatigue Crack Growth Mechanism of Polycrystalline Alloy Based on Crystal Plasticity and Extended Finite Element Method

Microstructure sensitivity of the low cycle fatigue crack initiation mechanisms for the Al 0.3 CoCrFeNi high entropy alloy: in-situ SEM study and crystal plasticity simulation

Microscopic fatigue crack propagation model for polycrystalline alloys

Crystallographic Mechanism for Crack Propagation in the T7451 Al–Zn–Mg–Cu Alloy

Crystal cracking of grain-gradient aluminum by a combined CPFEM-CZM method

Crystal plasticity modeling of low-cycle fatigue behavior of an Mg-3Al-1Zn alloy based on a model, including twinning and detwinning mechanisms

Influence of Grain Structure and Precipitates on Fatigue Crack Propagation Behaviors of Al-xCu-1.2Li-X Alloys

Influence of grain structure and precipitates on fatigue crack propagation behaviors of Al- x Cu-1.2Li-X alloys

A Crystal Plastic Finite Element Model for the Effect of Surface Integrity on Multiaxial Fatigue Life after Multistage Machining Processes

Micromechanical behavior of Ti-2Al-2.5Zr alloy under cyclic loading using crystal plasticity modeling

Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate