Abstract:The texture distribution, tensile property and fracture toughness of 7050 aluminum alloy thick plate were investigated by optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffractometry, tensile and toughness tests. The results show that the microstructure,texture,tensile property and fracture toughness are inhomogeneous in different layers along the thickness direction. At the same thickness, the tensile property and fracture toughness show appreciable anisotropy. From the surface to the center, the average sizes of the coarse second phase particles and recrystallization grains increase. Near the surface of the plate,typical shear textures {111}110 and cube textures {001}100 are observed, while the center of the plate shows typical β fiber texture with a scattering of cube texture. The quarter layer of the plate seems to serve as a transition layer. From the surface to the center, the strength is inhomogeneous in the rolling direction and long transverse direction. The strength in the center is smaller than that on the surface of the plate. The strength and fracture toughness show appreciable anisotropy at the same thickness. The strength in the rolling direction is higher than that in the long transverse direction and the short transverse direction, and the fracture toughness in the L-T orientation is higher than that in the T-L and S-L orientations at the same thickness. The fracture mode in the L-T orientation is trangranular fracture, and in the S-L orientation the fracture mode is intergranular fracture. In the T-L orientation, the fracture mode is a mixed fracture, the fraction of the trangranular fracture is lower than that in the L-T orientation, and the fraction of the intergranular fracture is lower than that in the S-L orientation.

Fracture Toughness and Fatigue Behavior of T7451 Al-Zn-Mg-Cu Alloy Thick Plate

Fracture Toughness and Fatigue Crack Growth Analysis of 7050-T7451 Alloy Thick Plate with Different Thicknesses

Characterization of Fracture and Fatigue Behavior of 7050 Aluminum Alloy Ultra-thick Plate

Fatigue Fracture of High-Strength Al-Zn-Mg-Cu Alloy

Inhomogeneity of Texture, Tensile Property and Fracture Toughness of 7050 Aluminum Alloy Thick Plate

Fatigue performance of 7475-T7351 aluminum alloy plate

The Fracture Behavior of 7085-T74 Al Alloy Ultra-Thick Plate During High Cycle Fatigue

Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate

Microstructure, Tensile Property and Fracture Toughness of 2397 Al-Li Alloy

Fatigue Fracture Characteristic of 7050-T7451 High-Strength Aluminum Alloy Thick Plate

On high‐cycle fatigue anisotropy of an aluminum alloy super‐thick plate

Study on Fatigue Behavior and Fracture Mechanism of LMD Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Alloy Based on Microstructure

Mechanical Anisotropy and Inhomogeneity through Thickness of 2297-T87 Aluminum Alloy Thick Plate

Fracture toughness and high-cycle fatigue behaviour of Al-Mg and Al-Mg-Sc-Zr alloys

The Effect of Inhomogeneous Microstructures on Strength and Stress Corrosion Cracking of 7085 Aluminum Alloy Thick Plate

Microstructure and Mechanical Properties of Al-Li Alloy 2397-T87 Rolled Plate

The Research of the Anisotropic Fatigue Behavior of 7475 Aluminum Alloy Plate

Fatigue crack propagation anisotropy of an Al–Zn–Mg–Cu super-thick plate

Fatigue behaviour of pre-strain 7B04-T7451 aluminum alloy

Influence of Solid Solution Treatment on Fatigue Crack Propagation Behavior in the Thickness Direction of 2519A Aluminum Alloy Thick Plates

Fatigue Crack Propagation Behavior of Al-Cu-Mg-Zr Alloy