Abstract:White-light OLED devices play an important application in information display fields. Optical interference of the microcavity structure has an important effect on device performances. According to the design of the band structure, ITO/MoO3 composite films were used as the anode, and Mg : Ag (1%) composite films were prepared by coevaporation as the translucent cathode; CuPc was used as the hole injection layer and anode passivation layer, NPB as the hole transmission layer and yellow light main material, rubrene as yellow dopant material, ADN as blue light main material, DSA-Ph as blue dopant material, and TPBi and Alq3 as the electron transport layers. We realized the change of the microcavity structure by adjusting the thickness of each organic functional layer film and simulated and calculated the optimized thickness of each organic film layer and influence on OLED device performances using the SimOLED software system. The optimized OLED microdisplay structure is Si(CMOS)/ITO (35 nm)/MoO3 (2 nm)/CuPc (5 nm)/2-TNATA (20 nm)/NPB (10 nm)/NPB : rubrene (1.5%)ADN : DSA-Ph (5%) (25 nm)/TPBi (15 nm)/Alq3 (1.2 nm)/Mg (13 nm) : Ag (1%). The optimized OLED microdisplay was prepared by the vacuum coating system, and the photoelectric performances of the OLED device were characterized by a spectral testing system consisting of the Photo Research PR655 spectrometer and Keithley 2400 program-controlled power supply. The effect of the microcavity structure on OLED device performances was studied. The results show that the variation of the film thickness of each organic functional layer has an important effect on the performances of OLED microdisplay, such as brightness and color coordinate, and the OLED microdisplay reaches a higher brightness of 3342 cd/m2 under the normal working voltage at 5.0 V after the structure is optimized, with CIE coordinate (0.28, 0.37), which is closer to the energy point of standard white light.

Study on Metal Microcavity OLEDs with Improved Efficiency

Optical Properties of Unsymmetrical Metal Microcavity in Organic Luminescent Devices

Optical trait of unsymmetrical metal microcavity in organic thin film luminescent devices

Low Operating-Voltage and High Power-Efficiency OLED Employing MoO3-doped CuPc As Hole Injection Layer

Microcavity OLED using Ag electrodes

High-Efficiency Microcavity Top-Emitting Organic Light-Emitting Diodes Using Silver Anode

The Microcavity Organic Light Emitting Device Based on Metal Induced Crystallized Poly-crystalline Si Film Anode

Tricolor Microcavity Oleds Based On P-Nc-Si:H Films As The Complex Anodes

Organic Microcavity Green Color Light Emitting Diode

Performance Optimization of Top-Emitting OLED Based on PEN Flexible Substrate with Microcavity

Improved Efficiency in Top-Emitting Oleds with P-Type Si Anode

High-Efficiency Bottom-Emitting Organic Light-Emitting Diodes with Double Aluminum As Electrodes

Design Simulation and Preparation of White OLED Microdisplay Based on Microcavity Structure Optimization

Highly Efficient Top-Emitting Organic Light-Emitting Devices with Aluminium Electrodes

Studies on a New Type of Metal Chelate OLED

Improvement of Light Extraction in Organic Light-Emitting Diodes Using A Corrugated Microcavity

Highly-efficient Low-voltage OLED Built by Controlling Hole-transport Characteristics With Metal-oxide Dopants

High-efficiency top-emitting organic light-emitting diodes based on metal/ITO composite electrodes

P‐124: Efficiency Enhanced Top Emitting OLED‐on‐Silicon Microdisplay with Aluminum Anode

Study of a New Type Anode of OLED by MIC Poly-Si

Top-emitting organic light-emitting device with high efficiency and low voltage using a silver–silver microcavity