Abstract:Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Ahead of Print. The research objectives of pilot diesel injection (PDI) ignition natural gas technology include high efficiency, clean combustion, and low pilot diesel mass. This study is based on a single-cylinder thermodynamic engine, combined with the CONVERGE simulation model and CHEMKIN chemical reaction kinetics model. The effects and mechanisms of various PDI strategies on the mixture equivalent ratio, temperature, and characteristics of combustion and emissions were investigated. The experimental results showed that the best PDI mass was 8 mg/cycle. The thermal atmosphere and activity in the cylinder were improved with an increase in PDI mass from 2 to 8 mg/cycle, which stabilized the mixture combustion. Further, the effects of different pilot injection timing (PIT) on combustion and emissions were investigated via experiments and simulation by controlling the operating conditions and maintaining a constant PDI total mass. The results show that the diesel had a single low-temperature reaction path when the PIT was close to the top dead center, whereas the PIT at the early stage of the compression stroke (CS) changed the chemical reaction path and accelerated the transformation of CH3 to CH2O, accumulating numerous active groups and accelerating the combustion rate, which is difficult to control the ignition phase. The reaction path of the double PDI strategy was similar to that of the PIT at the early CS stage, and its combustion is closed to premixed combustion; however, the accumulation of active groups was relatively small, and the combustion rate was relatively slow because the ignition phase was controlled by the second PDI, making the combustion phase easy to control. Finally, with the double PDI strategy that had the advantages of efficient combustion and avoidance of knock, the gross indicated thermal efficiency reached 49.3% that involved a −60°crank angle (CA) after top dead center (ATDC) first injection and −4°CA ATDC second injection.

In-Cylinder Mixture Distribution Research of Stratified Lean-Burn Strategy and Stratified Stoichiometric Strategy in a GDI Engine Using Laser-Induced Fluorescence

Analysis of Two-Stage Natural-Gas Lean Combustion Inside a Diesel Geometry

Effect of Spark Timing on the Combustion Stages Seen in a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

In-Cylinder Mixture Distribution Measurement in a GDI Engine Using Laser-Induced Fluorescence

In-Cylinder Mixture Distribution of Direct Injection LPG Using Laser-Induced Fluorescence

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Numerical investigation of the effect of fuel concentration stratification on gasoline compression ignition combustion under low-to-medium load conditions

Distributed Gas Ignition Using Injection Strategy for High Efficiency and Clean Combustion under Lean Condition

Co-evaporative multi-component fuel design for in-cylinder PLIF measurement and application in gasoline direct injection research

A comparative analysis of the performances of a syngas port injection plus gasoline direct injection combined-injection spark-ignition engine under lean-homogeneous charge and Lean-Stratified Charge modes

Optimizing Charge Stratification in a Lean-Burn Spark Ignition Engine

Methodology to Separate the Two Burn Stages of Natural-Gas Lean Premixed-Combustion Inside a Diesel Geometry

High-Speed Photography of Stratified Combustion in an Optical GDI Engine for Different Triple Injection Strategies

Numerical Investigations of Injection Timing Effects on a Gasoline Direct Injection Engine Performance: Part A, In-Cylinder Combustion Process

Optimising the Particulate Emission Characteristics of a Dual-Fuel Spark Ignition Engine by Changing the Gasoline Direct Injection Strategy

Effects of PFI/DI Injection on Stratified Flame Ignition SI-CAIHybrid Combustion

Experimental Investigation about the Effect of Double-Spark Plug Ignition on Combustion Characteristics for Motorcycle Gasoline Engines with a Mild Lean Mixture

Effects and mechanism of pilot diesel injection strategies on combustion and emissions of natural gas engine

Local Mixture Injection to Extend the Lean Limit of Spark-Ignition Engines