Abstract:In order to improve performance of internal combustion engines and meet the requirements of the new pollutant emission regulations, advanced combustion strategies have been investigated. The newly designed partially premixed combustion concept has demonstrated its potential for reducing NOx and particulate matter emissions combined with high indicated efficiencies while still retaining proper control over combustion process by using different injection strategies. In this study, parametric variations of injection pressure, second injection and third injection timings were experimentally performed to analyze the effect of the injection strategy over the air/fuel mixture process and its consequent impact on gaseous compound emissions and particulate matter emissions including its size distribution. Tests were carried out on a newly designed two-stroke high-speed direct injection compression-ignition engine operating with the partially premixed combustion concept using 95 research octane number gasoline fuel. A scanning particle sizer was used to measure the particles size distribution and the HORIBA 7100DEGR gas analyzer system to determine gaseous emissions. Three different steady-state operation modes in terms of indicated mean effective pressure and engine speed were investigated: 3.5 bar indicated mean effective pressure and 2000 r/min, 5.5 bar indicated mean effective pressure and 2000 r/min, and 5.5 bar indicated mean effective pressure and 2500 r/min. The experimental results confirm how the use of an adequate injection strategy is indispensable to obtain low exhaust emissions values and a balance between the different pollutants. With the increase in the injection pressure and delay in the second injection, it was possible to obtain a trade-off between NOx and particulate matter emission reduction, while there was an increase in hydrocarbon and carbon monoxide emissions under these conditions. In addition, the experiments showed an increase in particle number emissions and a progressive shift in the particles size distribution toward larger sizes, increasing the accumulation-mode particles and reducing the nucleation-mode particles with the decrease in the injection pressure and delay in the third injection.

Local Mixture Injection to Extend the Lean Limit of Spark-Ignition Engines

Two-Stage Lean-Burn Combustion Inside a Natural-Gas Spark-Ignition Engine with a Bowl-in-Piston Chamber

Effect of Spark Timing on the Combustion Stages Seen in a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

Local Charge Stratification In Spark-Ignition Engines

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

Optimizing Charge Stratification in a Lean-Burn Spark Ignition Engine

A comparative analysis of the performances of a syngas port injection plus gasoline direct injection combined-injection spark-ignition engine under lean-homogeneous charge and Lean-Stratified Charge modes

Effects of multiple injection strategies on gaseous emissions and particle size distribution in a two-stroke compression-ignition engine operating with the gasoline partially premixed combustion concept

In-Cylinder Mixture Distribution Research of Stratified Lean-Burn Strategy and Stratified Stoichiometric Strategy in a GDI Engine Using Laser-Induced Fluorescence

Lean combustion and EGR with charge stratification in a spark ignition engine

Quantitative mixing measurements and stochastic variability of a vaporizing gasoline direct-injection spray

Effects of spark ignition and stratified charge on gasoline HCCI combustion with direct injection

Fuel-air mixing process of low pressure direct injection in a side ported rotary engine

Effect of multi-injection strategy on characteristics of methanol-fueled direct injection spark ignition engine

Experimental study of fuel stratification for HCCI high load extension

A Lean Burn Gasoline Fueled Pre-Chamber Jet Ignition Combustion System Achieving High Efficiency and Low NOx at Part Load

Forced Ignition of a Rich Hydrogen/Air Mixture in a Laminar Counterflow: A Computational Study

Evaluating the potential of mixture formation methods to achieve efficient combustion and near-zero emissions on a hydrogen direct injection engine

Studies of Multi-Channel Spark Ignition of Lean N-Pentane/air Mixtures in a Spherical Chamber

Extending ultra-lean burn performance of high compression ratio pre-chamber jet ignition engines based on injection strategy and optimized structure