Abstract:Copper Zinc Tin Sulfide (Cu2ZnSnS4 or CZTS) is gaining much attention recently as a potential light absorber alternative to CuInGaSe2 due to its suitable energy band gap ∼1.5 eV with p-type conductivity, high optical absorption coefficient of ∼105 cm−1. Moreover, all its constituents are abundant in the crust of the earth and environmentally harmless. In the present investigation, CZTS thin films were prepared using simple two step process of, sulfurization of sequentially sputtered stack, Glass/Zn/Sn/Cu (hereafter CTZ) metallic precursors on soda lime glass substrate held at temperature 200 °C. The sputter power was optimized individually for Zn, Sn, and Cu layers. The sputtered CTZ precursors were annealed at different temperatures in the range, 300–550 °C with an increment of 50 °C for 2 h in the ambience of vaporized elemental sulfur. The XRD pattern revealed that the films sulfurized in the temperature range 300–400 °C showed various spurious (binary and ternary) phases and the films sulfurized at 450 °C exhibited a clear phase corresponding to CZTS that becomes predominant at 500 °C. The optimized (500 °C) CZTS thin films showed kesterite structure with (112) preferred orientation. The sharp Raman shift centered at 336 cm−1 confirms the single phase CZTS for the precursors sulfurized at 500 °C. From the transmittance measurements, the energy gap is found to be 1.62 eV for optimized CZTS films. The optical profilometer studies indicated an increase in the surface roughness with the sulfurization temperature. AFM measurements revealed compact morphology with pyramidal texture.

Effect of Sulfurization Temperature on Properties of Cu2sns3 Thin Films and Solar Cells Prepared by Sulfurization of Stacked Metallic Precursors

Synthesis and Optimized Sulfurization Time of Cu2SnS3 Thin Films Obtained from Stacked Metallic Precursors for Solar Cell Application

Effects of Sulfurization Temperature on the Structural and Optical Properties of Cu2CdSnS4 Thin Films Prepared by Direct Liquid Method

Effect of Sulfurization Process on the Properties of Solution-Processed Cu2SnS3 Thin Film Solar Cells

Sulfurization Temperature Dependent Physical Properties of Cu2SnS3 Films Grown by a Two-Stage Process

Effect of Cd Content and Sulfurization on Structures and Properties of Cd Doped Cu2SnS3 Thin Films

Effect of the stacking order, annealing temperature and atmosphere on crystal phase and optical properties of Cu2SnS3

Effect of Sulfurization Temperature of Solution-Processed Cu2SnS3 Absorber for Low Cost Photovoltaic Cells

Synthesis and Characterizations of Cu2MgSnS4 Thin Films with Different Sulfuration Temperatures

Study on the Preheating Duration of Cu2sns3 Thin Films Using Rf Magnetron Sputtering Technique for Photovoltaics

Phase composition of the earth-abundant Cu2SnS3 thin films with different annealing temperature and its effects on the performance of the related solar cells

The Effect of Substrate Temperature, Cu/Sn Ratio and Post-Annealing on the Phase-Change and Properties of Cu2SnS3 Film Deposited by Ultrasonic Spray Pyrolysis

Synthesis, Structure, Optics and Electrical Properties of Cu2FeSnS4 Thin Film by Sputtering Metallic Precursor Combined with Rapid Thermal Annealing Sulfurization Process

The role of sulfurization temperature on the morphological, structural and optical properties of electroplated Cu2MnSnS4 absorbers for photovoltaics

Sulfurization Temperature Effects on the Growth of Cu2ZnSnS4 Thin Film

Heating Rate Tuning in Structure, Morphology and Electricity Properties of Cu2FeSnS4 Thin Films Prepared by Sulfurization of Metallic Precursors

Fabrication and Characterization of Cu2znsns4 Thin Films for Photovoltaic Application by Low-Cost Single Target Sputtering Process

Investigation of the Sulfurization Process of Cu2sns3 Thin Films with Stacked Layers Cbd-Cu/Sns by Rapid Thermal Process

Influence of Sulfurization Temperature on Physical Properties of Cu2znsns4 Thin Films

Influence of Sulfurization Pressure on Cu2ZnSnS4 Thin Films and Solar Cells Prepared by Sulfurization of Metallic Precursors

Fabrication of Cu 2 SnS 3 thin-film solar cells with oxide precursor by pulsed laser deposition