Abstract:The oxidative reduced bulk polymerization system of MMA with BPO/DMA as composite initiator was used to study the effects of the ratio of BPO to DMA and the amount of overall initiator on the mechanical properties of the polymerized PMMA sheets, and the changes of the mechanical properties of the plates under high and low temperature conditions were studied. Thermoplastic PMMA was rarely exploited in continuous fiber‐reinforced composites due to its viscous high‐temperature molten fluid as well as pessimistic wettability into fiber fabric. Redox‐active polymerization is a green route to develop a new liquid PMMA resin at room temperature to provide an in situ curing with the advantages of energy saving and consumption reduction. In this paper, BPO/DMA was adopted as a redox initiator pair, and the effect of MMA:BPO:DMA ratio on curing time, Mn, Tg, and mechanical properties of PMMA were systematically studied. When the ratio of MMA:BPO:DMA is 200:1.2:1, PMMA‐200 achieved optimistic mechanical properties at 20°C (tensile strength, 64.7 MPa; tensile modulus, 3352 MPa; bending strength, 125.3 MPa; bending modulus, 3023 MPa). Moreover, the mechanical properties were further improved at low temperatures. The maximum tensile strength and tensile modulus were up to 97.43 and 4297 MPa (−40°C) respectively. The tensile strength (0°, 1103 MPa; 90°, 52.3 MPa) and tensile modulus (0°, 47.5 GPa; 90°, 14.2 GPa) of glass‐fiber‐reinforced PMMA composite at 20°C were found to be comparable with epoxy resin‐based composites and even higher at lower temperature. In summary, redox‐initiated PMMA and its fiber‐reinforced composites are promising thermoplastic materials as new lightweight alternatives. Highlights Preparation method of PMMA resin and glass fiber composite. Research on the mechanical properties, molecular weight, glass transition temperature, curing time, etc. of PMMA resin. Testing of mechanical properties of PMMA glass fiber composites at room temperature and low temperature. Current applications and prospects of PMMA glass fiber composites.

Time‐temperature‐transformation Diagram of Modified Resol Phenolic Resin and the Thermomechanical Performance of Resol Phenolic Resin/glass Fabric Composite

Preparation of glass fiber reinforced phenolic injection molding materials and its properties

Silicone-modified Phenolic Resin: Relationships Between Molecular Structure and Curing Behavior

Study of Post-curing Properties of Wood Flour Reinforced Phenolic Molding Materials

Effect of Processing Conditions on Physical Properties of 3‐aminophenoxyphthalonitrile/epoxy Laminates

Film forming technology and properties of modified resole phenolic resin via hot-melt method

Rheological, Dynamic Mechanical and Thermal Properties of Thermotropic Liquid Crystalline Polymer/Unsaturated Polyester/Glass Fiber Hybrid Composites

Influence of Long-Term Moisture Exposure and Temperature on the Mechanical Properties of Hybrid FRP Composite Specimens

Study on the Curing Behavior of Polythiol/phenolic/epoxy Resin and the Mechanical and Thermal Properties of the Composites

Improved Melt Processabilities of Thermosetting Polyimide Matrix Resins for High Temperature Carbon Fiber Composite Applications

Formability and Failure Mechanisms of Continuous Glass Fiber-Reinforced Polypropylene Composite Laminates in Thermoforming Below the Melting Temperature

Macro-mechanical Analysis of Tensile Strength of Glass/carbon Fiber Reinforced Plastics Hybrid Composites under Hydrothermal Environment

Synthesis and structure evolution of phenolic resin/silicone hybrid composites with improved thermal stability

A novel thermoplastic material: Pre‐polymerized PMMA liquid resin and continuous glass fiber‐reinforced composite initiated by benzoyl peroxide/N,N‐dimethylaniline

Designing a Low-Temperature Curable Phenolic/benzoxazine-Functionalized Phthalonitrile Copolymers for High Performance Composite Laminates

Curing Behavior And Processability Of Bmi/3-Apn System For Advanced Glass Fiber Composite Laminates

A Binary Resin System of Epoxy and Phenol-Formaldehyde for Improving the Thermo-Mechanical Behavior of FRP Composites

Study on Properties of Heat-Resistant Hybrid Resin Containing Silicon and Composites

Interphase Formation of a Resin Transfer Molded Silica–phenolics Composites Subjected to Dynamic Impregnation Process

Preparation and Properties of Molybdenum‐modified High‐ortho Thermosetting Phenolic Fiber

Development of the forming limit diagram for fiber-reinforced thermoplastic composites and its temperature effect