Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Rheological, Dynamic Mechanical and Thermal Properties of Thermotropic Liquid Crystalline Polymer/Unsaturated Polyester/Glass Fiber Hybrid Composites

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Effect of Monomer Structure on Crystallization and Glass Transition of Flexible Copolyesters

Blending Effects on Polymorphic Crystallization of Poly(l-lactide)

Liquid Crystalline Pet/60hba-Mwnts Composite: Synthesis, Characterization, and Properties

Thermomechanical Coupling in Glassy Polymers: an Effective Temperature Theory

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Preparation and properties of carbon fiber reinforced unsaturated polyester self-healing composites

Rheology and Processing of High-Strength Liquid Crystal Polymer Reinforced Thermoplastic Composite Materials

Dynamic Mechanical Properties and Thermal Properties of Longitudinal Basalt/Woven Glass Fiber Reinforced Unsaturated Polyester Hybrid Composites

Tribological and Mechanical Applications of Liquid-Crystal-Polymer-Modified Carbon-Fiber-Reinforced Polyamide–Polyurethane Composites

Thermal and Morphological Assessment of the Penta-Layered, Hybrid U-Polyester Composite Reinforced with Glass Fibers and Polypropylene

Processing and Property Study of MWCNT/Thermotropic Liquid Crystal Polymer Composite

Tribological Enhancement Effect of Main-Chain Thermotropic Liquid Crystalline Polymer

Effects of Polymer Micro-Structures on the Thermo-Optical Properties of a Flexible Soft-Mater Film Based on Liquid Crystals / Polymer Composite

Study on Thermotropic Liquid Crystalline Copolyamide/Polyamide 66 In situ Composites

Development of chopped glass fiber composites with difunctional benzoxazine and bio‐based phthalonitrile copolymer: A study of mechanical and thermomechanical properties

Anisotropic Mechanical Response and Strain Localization of a Metallic Glassy-Fiber-Reinforced Polyethylene Terephthalate Fabric

Glass/jute/sisal fiber reinforced hybrid polypropylene polymer composites: Fabrication and analysis of mechanical and water absorption properties

Effect of Glass Fiber on the Properties of Electrically Conductive Polyoxymethylene Composites

Synthesis and Analysis of Crystalline Unsaturated Polyester Used in LPMC