Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Tribological and Mechanical Applications of Liquid-Crystal-Polymer-Modified Carbon-Fiber-Reinforced Polyamide–Polyurethane Composites

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effects of Liquid Crystal Polymer (LCP) on the Structure and Performance of PEEK/CF Composites.

Tribological Enhancement Effect of Main-Chain Thermotropic Liquid Crystalline Polymer

Effect of Carbon Fiber Addition on the Tribological Properties of Polyoxymethylene Composites

Tribological Characteristics of Fibrous Polyphthalamide-Based Composites

Enhanced Mechanical and Tribological Properties in Polyphenylene Sulfide/polytetrafluoroethylene Composites Reinforced by Short Carbon Fiber

Remarkable enhancement of mechanical and tribological properties of polyamide 46/polyphenylene oxide alloy by polyurethane-coated carbon fiber

Mechanical Properties and Tribological Properties of Novolac Type Phenolic Blended with Liquid Crystalline Polyuethane

Effects of the Combination of Solid Lubricants and Short Carbon Fibers on the Sliding Performance of Poly(ether Imide) Matrix Composites

Tribological properties of perfluoropolymer fiber filled carbon fiber/polyphenylene sulfide composites: Effect of in‐situ fibrillated fiber or split fiber

Effect of Perfluoropolymers on the Anti-Wear Properties of Carbon Fiber/Polyphenylene Sulfide Composites: A Comparative Study

Tribological Properties of Solid Lubricants Filled Glass Fiber Reinforced Polyamide 6 Composites

Tribological and mechanical behaviors of polyamide 6/glass fiber composite filled with various solid lubricants.

Friction and Wear Mechanisms of Pa66/Pps Blend Reinforced with Carbon Fiber

Tribological and Mechanical Properties of Graphite/Polytetrafluoroethylene/Glass Fiber Filled Polyamide 6 Composite

Rheology and Processing of High-Strength Liquid Crystal Polymer Reinforced Thermoplastic Composite Materials

Improvement in the tribological properties of polyamide 6: Talc, glass fiber, graphite, and ultrahigh-molecular-weight polyethylene

In Situ Micro-Fibrillization and Post Annealing to Significantly Improve the Tribological Properties of Polyphenylene Sulfide/polyamide 66/polytetrafluoroethylene Composites

Effect of solid lubricants on tribological behavior of glass fiber reinforced polyamide 6

Effect of perfluoroalkylmethacrylate ester-grafted-linear low-density polyethylene on the tribological property of polyoxymethylene-linear low-density polyethylene composites