Abstract:As the range of applications for fiber-reinforced polymer (FRP) composite materials in civil engineering constantly increases, there is more and more concern with regard to their performance in critical environments. The fire behavior of composite materials is especially important since complex physical and chemical processes such as the glass transition and decomposition occur when these materials are subjected to elevated and high temperatures, possibly leading to considerable loss of stiffness and strength. This stiffness and strength degradation in composite materials under elevated and high temperatures is the result of changes in polymer molecular structures. When polyester thermosets are subjected to elevated and high temperatures, they undergo three transitions (glass transition, leathery-to-rubbery transition, and rubbery-to-decomposed transition), corresponding to four different states (glassy, leathery, rubbery and decomposed). At a certain temperature, a composite material can therefore be considered as a mixture of materials that are in different states. As the content of each state varies with temperature, the composite material exhibits temperature-dependent properties. Since these changes in state can be described using kinetic theory, the quantity of material in each state can be estimated and the thermophysical and thermomechanical properties of the mixture can thus be determined. These concepts formed a basis for the development of thermophysical and thermomechanical property sub-models for composites at elevated and high temperatures and even for the description of post-fire status. Incorporating these thermophysical property sub-models into a heat transfer governing equation, thermal responses were calculated using a finite difference method. Integrating the thermomechanical property sub-models within structural theory, the mechanical responses were described using a finite element method and the time-to-failure was also predicted by defining a failure criterion. The modeling results for temperature responses, mechanical responses and post-fire behavior were compared with those obtained from structural endurance experiments on full-scale cellular GFRP (glass fiber-reinforced polymer, in this case polyester resin) panels subjected to a four-point bending configuration and fire from one side. The modeling results for time-to-failure were compared with those from the experiments carried out on GFRP tubes under combined compressive and thermal loadings. In each experimental setup, two different thermal boundary conditions were investigated – with and without water cooling through specimen cells – and good agreement was found. The understanding gained and modeling of the behavior of GFRP composites under elevated and high temperatures carried out in this thesis could be applicable for different composite materials, and also benefit investigations regarding both active and passive fire protection techniques in order to improve the fire resistance of structures made of such materials.

Development of the forming limit diagram for fiber-reinforced thermoplastic composites and its temperature effect

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

Failure behavior of a glass-fiber reinforced thermoplastic composite

Formability and Failure Mechanisms of Continuous Glass Fiber-Reinforced Polypropylene Composite Laminates in Thermoforming Below the Melting Temperature

Influence of Temperature on the Impact Behavior of Woven-Ply Carbon Fiber Reinforced Thermoplastic Composites

The Synergistic Effect of Temperature and Loading Rate on Deformation for Thermoplastic Fiber Metal Laminates

Mechanical Properties of High-Temperature Fiber-Reinforced Thermoset Composites with Plain Weave and Unidirectional Carbon Fiber Fillers

Material and Structural Performance of Fiber-Reinforced Polymer Composites at Elevated and High Temperatures

Atomistic Modeling of the Effect of Temperature on Interfacial Properties of 3D-Printed Continuous Carbon Fiber-Reinforced Polyamide 6 Composite: From Processing to Loading

The Out-of-Plane Compression Response of Woven Thermoplastic Composites: Effects of Strain Rates and Temperature

Temperature-dependent strength modeling of fiber-reinforced composites considering critical properties evolution

Thermomechanical Behavior and Microstructure Properties of Carbon Fiber Reinforced Polymer at Elevated Temperatures

Effects of high temperature and strain rate on the impact-induced inter-laminar shear behavior of plain woven CF/PEEK thermoplastic composites

High-Temperature Effect on the Tensile Mechanical Properties of Unidirectional Carbon Fiber-Reinforced Polymer Plates

Elevated temperature effect on tension fatigue behavior and failure mechanism of carbon/epoxy 3D angle-interlock woven composites

Evaluation of Tensile properties of FRP Composite Laminates under Varying Strain Rates and Temperatures

Failure Behavior And Performance Analysis Of Hybrid-Fiber Reinforced Paek Composites At High Temperature

Thermo-visco mechanical behavior of glass fiber reinforced thermoplastic composite

Mechanical Behavior and Design of FRP Structural Members at High and Low Service Temperatures

Influence On The Mechanical Behavior Of Carbon Fiber Fabric Reinforced Pps Laminates Under Different Temperature

A comprehensive study of low-velocity impact behavior and damage evaluation of angle-ply thin woven GFRP composites under various temperatures