Abstract:The present experimental study assesses the mechanical properties of glass/carbon/glass hybrid composite laminates after being exposed to moisture in a deep freezer and elevated temperatures for extended periods. The top and bottom layers of the hybrid laminates are reinforced with glass fibre, and the middle layer is reinforced with carbon fibre using the epoxy matrix as a binder polymer material. The hybrid laminates were manufactured using the resin transfer moulding method, and their compressive and tensile properties were determined using a tensile testing machine. The storage modulus, loss modulus, and damping factors of all groups of laminates were identified using a dynamic mechanical analysis as a function of temperature and vibration frequency. The experimental results on compressive and tensile properties revealed slight variations when the hybrid laminates were kept at low temperatures in a deep freezer for extended periods. This might occur due to the increasing molecular crosslinking of the polymer network. As the testing temperature increased, compressive, tensile, storage modules, loss modulus, and damping factors decreased. This might occur due to the increasing mobility of the binder material. Particularly, the highest stiffness parameters were obtained at −80 °C/GCG (glass/carbon/glass) laminates due to the presence of a beta transition in the glassy region. The relationships between the glass transitions and the targeted frequencies were characterized. The values of the glass transition shift towards higher temperatures as the frequency increases. This might occur due to a reduction in the gaps between the crosslinking of the epoxy network when the frequency increases. The accuracy of the storage modulus results was compared with the empirical models. The model based on the Arrhenius law provided the closest correlation. Meanwhile, another model was observed that was not accurate enough to predict when gamma and beta relaxations occur in a glassy state.

On-axis and Off-Axis Compressive Behavior of Pultruded GFRP Composites at Elevated Temperatures

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

Mechanical Properties and Microstructures of Steel-basalt Hybrid Fibers Reinforced Cement-based Composites Exposed to High Temperatures

Correlation Between Macroscopic Properties and Microscopic Pore Structure in Steel-Basalt Hybrid Fibers Reinforced Cementitious Composites Subjected to Elevated Temperatures

Effects of temperature and strain rate on impact compression behaviors of three-dimensional carbon fiber/epoxy braided composites

Axial Crush Behavior and Energy Absorption Capability of Foam-Filled GFRP Tubes under Elevated and High Temperatures

Influence of strain rate and temperature on mechanical properties of carbon woven-ply PPS thermoplastic laminates under dynamic compression

Mechanical Behavior and Design of FRP Structural Members at High and Low Service Temperatures

Energy-absorption properties of foam-filled composite tubes at elevated temperatures

The Out-of-Plane Compression Response of Woven Thermoplastic Composites: Effects of Strain Rates and Temperature

The three-point bending responses of carbon fiber composite sandwich beams with Y-frame cores at high and low temperatures

Evolution of strain-rate dependent compressive failure behavior of ceramifiable FRP composites at high temperature conditions

Transverse impacts‐induced deformation and damage of 3D angle‐interlock woven composites at elevated temperatures

Effect of temperature on bending behavior of woven fabric-reinforced PPS-based composites

Influence of Hygrothermal Aging on the Durability and Interfacial Performance of Pultruded Glass Fiber-Reinforced Polymer Composites

Effects of temperature and fiber orientation on the tensile behavior of short carbon fiber reinforced PEEK composites

Elevated temperature effect on tension fatigue behavior and failure mechanism of carbon/epoxy 3D angle-interlock woven composites

Influence of Long-Term Moisture Exposure and Temperature on the Mechanical Properties of Hybrid FRP Composite Specimens

High-Temperature Effect on the Tensile Mechanical Properties of Unidirectional Carbon Fiber-Reinforced Polymer Plates

The effects of temperature and hygrothermal aging on the properties of CF/PA6 composite and its compression failure mechanisms

Mechanical Behavior of GFRP Laminates Exposed to Thermal and Moist Environmental Conditions: Experimental and Model Assessment