Abstract:Considering the anisotropy of microstructure of additive manufactured metal materials, quantitative assessment of the anisotropy of fatigue crack growth (FCG) behavior is necessary for structural damage tolerance design and evaluation. This study conducted an experimental and mechanistic investigation of the FCG behavior of the laser metal deposited (LMD) Ti-6Al-4V alloy, focusing on the anisotropy of FCG and the effect of overload on FCG. Both the FCG experiments with constant amplitude loading (CAL) and with a single overload (OL) were performed in different directions. Under CAL, the FCG rate exhibits a bilinear correlation with the stress intensity factor. Before the transition point (Δ K T =16.9 MPa√m), since the grain boundaries are sparser along the columnar crystal growth direction, the FCG rate in the XY specimen is higher than that in the other directions. When the FCG rate further increases, the hindrance effect of grain boundaries on FCG weakens, and the anisotropy of FCG rates disappears. An interesting new finding is that when an overload is applied after Δ K T , the FCG rates in the XZ and ZX directions become different, and the overload-induced anisotropy increases with the overload ratio (OLR). The difference in FCG rates between the two directions exceeds 23.2% when OLR is 2.5. Based on microscopic and theoretical analysis, it was demonstrated that the overload induces residual strain in front of the crack-tip and enhances FCG resistance. The FCG resistance is positively related to the size of the plastic zone and negatively related to the yield strength in the loading direction.

Fatigue Crack Tip Strain Evolution and Crack Growth Prediction under Single Overload in Laser Melting Deposited Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Titanium Alloy

DIC-based Studies of the Overloading Effects on the Fatigue Crack Propagation Behavior of Ti-6Al-4V ELI Alloy

Effects of Tensile/compressive Overloads on Fatigue Crack Growth Behavior of an Extra-Low-interstitial Titanium Alloy

Instrumented indentation measurements of residual stresses around a crack tip under single tensile overloads

Overload-induced anisotropy of fatigue crack growth in laser deposited Ti-6Al-4V alloy

Near-tip Strain Evolution and Crack Closure of Growing Fatigue Crack under a Single Tensile Overload

Fatigue limit prediction model and fatigue crack growth mechanism for selective laser melting Ti6Al4V samples with inherent defects

Failure Behavior of Laser Metal Deposited Additive Manufacturing Ti-6Al-4V: Effects of Stress State and Initial Defects

A Study on Fatigue Crack Closure Associated with the Growth of Long Crack in a New Titanium Alloy

Investigating dwell fatigue crack growth in welded titanium alloy structures

Molecular dynamics simulation of effects of loading parameters on fatigue crack growth behavior in titanium single crystal

In-situ investigation on tensile deformation and fracture behaviors of inhomogeneous microstructure during laser repair of Ti-6Al-4 V titanium alloy

STUDY OF FATIGUE CRACK GROWTH RETARDATION, CRACK TIP DEFORMATION AND CRACK CLOSURE UNDER SINGLE OVERLOAD APPLICATION FOR A537 STEEL

Numerical investigation of mechanical behavior of crack tip under mode I and mixed-mode I-II fatigue loading at negative load ratios

Prediction of Fatigue Crack Growth Retardation Using a Cyclic Cohesive Zone Model

Life Prediction and Failure Analysis in Laser Powder Bed Fused TiC/Ti6Al4V Titanium Matrix Composite under High Cycle and Very High Cycle Fatigue Conditions

Study on Fatigue Crack Growth of Electron Beam Selective Melting of Titanium Alloy

Gradient microstructure and foreign-object-damaged fatigue properties of Ti6Al4V titanium alloy processed by the laser shock peening and subsequent shot peening

Fatigue crack growth under mixed mode I-II loading with a single tensile overload at negative load ratios

Micro-deformation behavior of laser melting deposited multi-gradient TC4/TC11 alloy under tension-tension cyclic loading

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio