Abstract:In the serviced components of a 7075 aluminum alloy, the propagation of fatigue crack can be retarded because of the overload effect; however, the corresponding retardation mechanisms are complex. To provide further insights into the retardation mechanisms of 7075 aluminum alloys, this study addresses the crack tip damage response of a cracked 7075 aluminum alloy under an overload effect. Based on the dual-scale modeling approach and the damage-coupled crystal plasticity model, the effect of the microstructure of a 7075 aluminum alloy on the damage behavior ahead of the crack tip under an overload was studied. The factors affecting fatigue damage accumulation ahead of the crack tip, such as dislocation density, the variation in the activities of slip systems, and the orientation effect of the nearest neighbor grains, are described. The results show that for the 7075 aluminum alloy, the compressive residual stress induced by the overload effect not only decreases the number of activated slip systems, but also lowers the rate of increase in dislocation density. This causes a decrease in fatigue damage accumulation during deformation. Moreover, the overload effect decreases the slip system activity as well as the resultant plastic slip; however, the decrease in plastic slip varies with the grain orientation, indicating that the overload effect depends on the grain orientation. It can also be found that both the damage strain energy release rate and lattice strain are influenced by the orientation of the nearest neighbor grains, which can eventually affect the overload effect. These findings contribute to understanding the retardation mechanisms from a microscopic perspective and provide guidance on improving the material design of a 7075 aluminum alloy to some extent.

DIC-based Studies of the Overloading Effects on the Fatigue Crack Propagation Behavior of Ti-6Al-4V ELI Alloy

Effects of Tensile/compressive Overloads on Fatigue Crack Growth Behavior of an Extra-Low-interstitial Titanium Alloy

A Study of the Back Stress and the Friction Stress Behaviors of Ti-6Al-4V Alloy During Low Cycle Fatigue at Room Temperature

Instrumented indentation measurements of residual stresses around a crack tip under single tensile overloads

Overload-induced anisotropy of fatigue crack growth in laser deposited Ti-6Al-4V alloy

STUDY OF FATIGUE CRACK GROWTH RETARDATION, CRACK TIP DEFORMATION AND CRACK CLOSURE UNDER SINGLE OVERLOAD APPLICATION FOR A537 STEEL

Short fatigue crack growth: overload-induced acceleration/retardation behavior

High-temperature Fatigue Crack Propagation Study of Superalloy GH4169 by Single-Lens 3D Digital Image Correlation

Experimental investigation of overload effects on fatigue crack growth behaviour of 7050‐T7451 aluminium alloy

Investigation on Fatigue Threshold Testing Methods in a Near Lamellar TiAl Alloy

Crack initiation and propagation in Ti-6Al-4V-0.55Fe alloy subjected to the low-cycle dwell-fatigue

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio

Effects of stress ratio on high-cycle and very-high-cycle fatigue behavior of a Ti–6Al–4V alloy

An Investigation of Small-crack and Long-crack Propagation Behavior in Titanium Alloy TC4 and Aluminum Alloy 7475-T7351

The Overload Effect on the Crack Tip Damage Mechanism in a 7075 Aluminum Alloy

In-plane biaxial low-cycle dwell fatigue behavior of CP-Ti based on DIC method

Stress-sensitive fatigue crack initiation mechanisms of coated titanium alloy

Effect of stress ratio and overload on mixed-mode crack propagation behaviour of EA4T steel

Study on the crack nucleation mechanism of Ti-2Al-2.5Zr alloy in low cycle fatigue: Quasi in-situ experiments and crystal plasticity simulation

Study on Fracture Behavior of Nickel-Based Single Crystal Superalloy Subjected to High Temperature Fatigue Using Digital Image Correlation

Fatigue crack growth under mixed mode I-II loading with a single tensile overload at negative load ratios