Abstract:Development of large bandgap (1.80-1.85 eV Eg) perovskite is crucial for perovskite-perovskite tandem solar cells. However, the performance of 1.80-1.85 eV Eg perovskite solar cells (PVKSCs) are significantly lagging their counterparts in the 1.60-1.75 eV Eg range. This is because the photovoltage ( Voc) does not proportionally increase with Eg due to lower optoelectronic quality of conventional (MA,FA,Cs)Pb(I,Br)3 and results in a photovoltage plateau ( Voc limited to 80% of the theoretical limit for ∼1.8 eV Eg). Here, we incorporate phenylethylammonium (PEA) in a mixed-halide perovskite composition to solve the inherent material-level challenges in 1.80-1.85 eV Eg perovskites. The amount of PEA incorporation governs the topography and optoelectronic properties of resultant films. Detailed structural and spectroscopic characterization reveal the characteristic trends in crystalline size, orientation, and charge carrier recombination dynamics and rationalize the origin of improved material quality with higher luminescence. With careful interface optimization, the improved material characteristics were translated to devices and Voc values of 1.30-1.35 V were achieved, which correspond to 85-87% of the theoretical limit. Using an optimal amount of PEA incorporation to balance the increase in Voc and the decrease in charge collection, a highest power conversion efficiency of 12.2% was realized. Our results clearly overcome the photovoltage plateau in the 1.80-1.85 eV Eg range and represent the highest Voc achieved for mixed-halide PVKSCs. This study provides widely translatable insights, an important breakthrough, and a promising platform for next-generation perovskite tandems.

Pushing the Envelope: Achieving an Open‐Circuit Voltage of 1.18 V for Unalloyed MAPbI3 Perovskite Solar Cells of a Planar Architecture

Efficient and Stable Large Bandgap MAPbBr<sub>3</sub> Perovskite Solar Cell Attaining an Open Circuit Voltage of 1.65 V

Achieving High Open‐Circuit Voltages Up to 1.57 V in Hole‐Transport‐Material‐Free MAPbBr3 Solar Cells with Carbon Electrodes

Phase Engineering of Perovskite Materials for High-Efficiency Solar Cells: Rapid Conversion of CH3NH3PbI3 to Phase-Pure CH3NH3PbCl3 Via Hydrochloric Acid Vapor Annealing Post-Treatment

A Versatile Molten‐salt Induction Strategy to Achieve Efficient CsPbI3 Perovskite Solar Cells with a High Open‐circuit Voltage >1.2 V

Oxygen Intercalation Induced by Photocatalysis on the Surface of Hybrid Lead Halide Perovskites

Mixed-Organic-Cation (FA)x(MA)1-xPbI3 Planar Perovskite Solar Cells with 16.48% Efficiency via a Low-Pressure Vapor-Assisted Solution Process

Stable Pure Iodide MA0.95Cs0.05PbI3 Perovskite Toward Efficient 1.6 Ev Bandgap Photovoltaics.

Coordinating light management and advance metal nitride interlayer enables MAPbI3 solar cells with >21.8% efficiency

Engineering the Hole Extraction Interface Enables Single‐Crystal MAPbI 3 Perovskite Solar Cells with Efficiency Exceeding 22% and Superior Indoor Response

Crystallization and Defect Chemistry Dual Engineering for MAPbI 3 Perovskite Solar Cells with Efficiency Approaching 22%

Wide-bandgap MAPbBr 3 perovskite solar cells using bifunctional-molecule additives achieving a high open-circuit voltage of 1.63 V

Open-Circuit Voltages Exceeding 1.26 V in Planar Methylammonium Lead Iodide Perovskite Solar Cells

Overcoming the Photovoltage Plateau in Large Bandgap Perovskite Photovoltaics

Suppressing charge recombination in a methylammonium-free wide-bandgap perovskite film for high-performance and stable perovskite solar cells

Semitransparent CH3NH3PbI3 Films Achieved by Solvent Engineering for Annealing‐ and Electron Transport Layer‐Free Planar Perovskite Solar Cells

The CsPbI2Br perovskite solar cell with high Voc by crystallization optimization

Light Processing Enables Efficient Carbon-Based, All-Inorganic Planar CsPbIBr2 Solar Cells with High Photovoltages

Pure 2D Perovskite Formation by Interfacial Engineering Yields a High Open‐Circuit Voltage beyond 1.28 V for 1.77‐eV Wide‐Bandgap Perovskite Solar Cells

Achieving High Open‐Circuit Voltage for P‐i‐n Perovskite Solar Cells Via Anode Contact Engineering

High-Voltage-Efficiency Inorganic Perovskite Solar Cells in a Wide Solution-Processing Window