Abstract:CONSPECTUS: To tackle the foreseen energy crisis and serious environmental problem caused by conventional energy resources, solar cells, or photovoltaics (PV), a technology that can directly convert sunlight to electricity has been considered to be one of the most important and cost-effective clean energy techniques that benefit the environment. So far, silicon-based PVs have dominated the market due to mature fabrication techniques and their relatively good power conversion efficiency (PCE) and excellent stability. In the past decades, metal halide perovskite PVs have been a major direction of current PV research owing to their intriguing optoelectronic performance. The record PCE of perovskite PV cells has unprecedently increased from an original 3.8 to 25.5%. The typical structure of a photovoltaic perovskite is ABX(3), where A refers to a monovalent cation such as methylammonium (MA(+)), cesium (Cs+), or formamidinium (FA(+)); B refers to a divalent cation such as Pb2+ or Sn2+; and X refers to a halide anion. In general, a perovskite PV device consists of an active layer of the perovskite absorber, which is connected by a hole-transporting layer (HTL) and an electron-transporting layer (ETL). In the beginning, the strategies to improve the PCEs mainly focused on developing an effective method to grow a smooth and continuous polycrystalline film. After the improvement of the baseline PCE of the perovskite PVs, various techniques were employed to reduce the defects of perovskite formed at grain boundaries and surfaces, further pushing the PCEs of perovskite PV devices to over 20%. In the meantime, the discovery of suitable and low-cost interfacial materials such as electron-transporting materials and hole-transporting materials has appealed to the attention of the perovskite research community to accelerate the commercialization of the perovskite PVs. In this Account, we start from our efforts to develop facile and effective fabrication strategies to obtain smooth and continuous polycrystalline perovskite thin films, including vapor-assisted and moisture-assisted perovskite crystal growth. The strategies and the in-depth mechanisms of preventing the formation of specific detrimental defects accumulated at grain boundaries or the surface are also portrayed by designing various passivation molecules with certain functional groups, such as carbonyl groups, amine groups, or sulfonic groups. Some systematically designed electron- or hole-transporting materials to improve the charge extraction and collection efficiency in perovskite PV devices are discussed as well. Finally, future perspectives for further enhancing the long-term stability and PCE are proposed to accelerate the commercialization of perovskite PV devices in the next decade.

Overcoming the Photovoltage Plateau in Large Bandgap Perovskite Photovoltaics

Wide-Gap Perovskite Via Synergetic Surface Passivation and Its Application Toward Efficient Stacked Tandem Photovoltaics.

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Scalable growth of stable wide‐bandgap perovskite towards large‐scale tandem photovoltaics

Suppressing Phase Segregation in Wide Bandgap Perovskites for Monolithic Perovskite/Organic Tandem Solar Cells with Reduced Voltage Loss

Enhanced Photovoltage for Inverted Planar Heterojunction Perovskite Solar Cells

Regulating surface potential maximizes voltage in all-perovskite tandems

Interface optimization and growth control for high efficiency wide bandgap perovskite solar cells

Simultaneous Band-Gap Narrowing and Carrier-Lifetime Prolongation of Organic-Inorganic Trihalide Perovskites

Pure 2D Perovskite Formation by Interfacial Engineering Yields a High Open‐Circuit Voltage beyond 1.28 V for 1.77‐eV Wide‐Bandgap Perovskite Solar Cells

Record Open‐Circuit Voltage Wide‐Bandgap Perovskite Solar Cells Utilizing 2D/3D Perovskite Heterostructure

Stabilizing Wide‐Bandgap Perovskite with Nanoscale Inorganic Halide Barriers for Next‐Generation Tandem Technology

High Open‐Circuit Voltage Wide‐Bandgap Perovskite Solar Cell with Interface Dipole Layer

Breaking 1.7V open circuit voltage in large area transparent perovskite solar cells using bulk and interfaces passivation

Ideal Bandgap Organic–Inorganic Hybrid Perovskite Solar Cells

Breaking 1.7 V Open Circuit Voltage in Large Area Transparent Perovskite Solar Cells Using Interfaces Passivation

Synergistic Effect of Ammonium Salts in Sequential Deposition toward Efficient Wide-Band-Gap Perovskite Photovoltaics with PCE Exceeding 20%

Crystallization Regulation and Defect Passivation for Efficient Inverted Wide‐Bandgap Perovskite Solar Cells with over 21% Efficiency

Enhanced Quasi-Fermi Level Splitting of Perovskite Solar Cells by Universal Dual-Functional Polymer

Triple-halide Wide-Bandgap Perovskites Tailored Via Facile Organic Halide Treatment for High-Performance Perovskite/cu(in,ga)se2 Tandem Solar Cells

Enhanced charge transport of wide-bandgap perovskite solar cells enabled by crown ether-mediated crystal modulation