Abstract:Efficient semi-transparent solar cells can trigger the adoption of building integrated photovoltaics. Halide perovskites are particularly suitable in this respect owing to their tunable bandgap. Main drawbacks in the development of transparent perovskite solar cells are the high Voc deficit and the difficulties in depositing thin films over large area substrates, given the low solubility of bromide and chloride precursors. In this work, we develop a 2D and passivation strategies for the high band-gap Br perovskite able to reduce charge recombination and consequently improving the open-circuit voltage. We demonstrate 1cm 2 perovskite solar cells with Voc up to 1.73 V (1.83 eV QFLS) and a PCE of 8.2%. The AVT exceeds 70% by means of a bifacial light management and a record light utilization efficiency of 5.72 is achieved, setting a new standard for transparent photovoltaics. Moreover, we show the high ceiling of our technology towards IoT application due to a bifaciality factor of 87% along with 17% PCE under indoor lighting. Finally, the up-scaling has been demonstrated fabricating 20cm 2 -active area modules with PCE of 7.3% and Voc per cell up to 1.65V.

What problem does this paper attempt to address?

This paper focuses on improving the performance of large-area transparent perovskite solar cells, especially addressing the issue of low open circuit voltage (Voc). The research team has reduced charge recombination in high-bandgap Br-based perovskite by using 2D structure and interface passivation strategies, which enhances Voc. They have demonstrated a 1 cm² perovskite solar cell achieving a Voc of up to 1.73 V (corresponding to a Quasi-Fermi Level Splitting exceeding 1.83 eV) and a power conversion efficiency (PCE) of 8.2%. Moreover, by employing double-sided light management, an average visible light transmittance (AVT) of over 70% and a light utilization efficiency of 5.72% were achieved, setting a new standard for transparent photovoltaic technology. The paper also addresses the challenges of depositing large-area films, which is a difficulty in transparent perovskite solar cells due to the low solubility of bromide precursors. The research team used novel large-volume cations (such as neo-Pentylammonium chloride and iso-Pentylammonium chloride) to passivate defects and form 2D wide bandgap perovskite layers, thereby improving cell performance. Experimental results show that these strategies reduce surface defects, enhance Voc, and enable the fabrication of high-performance films on large-size substrates through optimized solvent anti-solvent strategies. The paper also discusses the scalability of the technology and presents a module with an active area of 20 cm², achieving a PCE of 7.3% and a single-cell Voc of 1.65 V. Furthermore, these cells exhibit excellent performance under indoor low-light conditions, with a bifaciality factor of 87% and a PCE of 17%, demonstrating their potential for Internet of Things applications. The research also highlights the potential impact of these technologies on building-integrated photovoltaics (BIPV), particularly in urban environments where vertical surfaces can be utilized for energy harvesting.

Breaking 1.7V open circuit voltage in large area transparent perovskite solar cells using bulk and interfaces passivation

Breaking 1.7 V Open Circuit Voltage in Large Area Transparent Perovskite Solar Cells Using Interfaces Passivation

Wide-Gap Perovskite Via Synergetic Surface Passivation and Its Application Toward Efficient Stacked Tandem Photovoltaics.

Highly Efficient Semitransparent Solar Cells with Selective Absorption and Tandem Architecture.

Multimodal Approach towards Large Area Fully Semitransparent Perovskite Solar Module

Flexible, Transparent, and Bifacial Perovskite Solar Cells and Modules Using the Wide-Band Gap FAPbBr 3 Perovskite Absorber

Ultra-thin high efficiency semitransparent perovskite solar cells

Semitransparent perovskite solar cells with an evaporated ultra-thin perovskite absorber

Semitransparent Perovskite Solar Cells with an Evaporated Ultra‐Thin Perovskite Absorber

Record Open‐Circuit Voltage Wide‐Bandgap Perovskite Solar Cells Utilizing 2D/3D Perovskite Heterostructure

Dual Interfacial Modifications Enable High Performance Semitransparent Perovskite Solar Cells with Large Open Circuit Voltage and Fill Factor

Semi‐transparent blade‐coated FAPbBr3 perovskite solar cells: A scalable low‐temperature manufacturing process under ambient condition

Scalable Ambient Fabrication of High-Performance CsPbI2Br Solar Cells

Br Vacancy Defects Healed Perovskite Indoor Photovoltaic Modules with Certified Power Conversion Efficiency Exceeding 36%

Pure 2D Perovskite Formation by Interfacial Engineering Yields a High Open‐Circuit Voltage beyond 1.28 V for 1.77‐eV Wide‐Bandgap Perovskite Solar Cells

Efficient Semi-Transparent Wide-Bandgap Perovskite Solar Cells Enabled by Pure-Chloride 2D-Perovskite Passivation

Overcoming the Photovoltage Plateau in Large Bandgap Perovskite Photovoltaics

Dual-Passivation Strategy with Escaped Thiocyanate and Sturdy Chloride toward Large-Scale Wide-Band-Gap Perovskite Modules

Open-circuit and short-circuit loss management in wide-gap perovskite p-i-n solar cells

Investigating the Balance between Power Conversion Efficiency and Average Visible Transmittance for Semitransparent Perovskite Solar Cells