Abstract:Sb2S3 is a promising environmentally‐friendly semiconductor for stable and high efficiency thin film solar cells, but, like many other polycrystalline materials, is limited by non‐radiative recombination and carrier scattering by grain boundaries. Herein, we show how the grain boundary density in Sb2S3 films can be significantly reduced from 1068±40 nm μm−2 (largest grain ∼5 μm) to 327±23 nm μm−2 (largest grain >15 μm) by incorporating an appropriate amount of Ce3+ into the precursor solution for Sb2S3 deposition. Through extensive characterization of the structural, morphological and optoelectronic properties, complemented with computations, we reveal the underlying mechanisms responsible for the increased grain size and improved photovoltaic performance of Sb2S3 solar cells. A critical factor behind the reduction in grain boundary density is the formation of an ultrathin layer of Ce2S3 at the CdS/Sb2S3 interface, which could reduce the interfacial energy and increase the adhesion work between Sb2S3 and the substrate to encourage heterogeneous nucleation of Sb2S3, as well as increase the rate of grain growth. Through a reduction in non‐radiative recombination at grain boundaries and/or the CdS/Sb2S3 heterointerface as well as improved charge‐carrier transport properties at the heterojunction, we achieved high performance Sb2S3 solar cells with a power conversion efficiency reaching 7.66%, and an open‐circuit voltage (VOC) of 796 mV. This VOC is the highest reported thus far for Sb2S3 solar cells. This work provides a strategy to simultaneously regulate the nucleation and growth of Sb2S3 absorber films via in‐situ chemical environment tuning, which can be more broadly applied to other thin film systems to improve their photovoltaic performance. This article is protected by copyright. All rights reserved

In Situ Growth of CuSbS2 Thin Films by Reactive Co-Sputtering for Solar Cells

Preparation and Characterization of Cuins2 Thin Films for Solar Cells by Chemical Bath Deposition

Synthesis and Characterization of Hydrazine Solution Processed Cu12Sb4S13 Film

Self-assembled growth of quasi-vertically oriented Sb2S3 thin films for substrate structured solar cells

Chemical synthesis of Cu(In) metal inks to prepare CuInS2 thin films and solar cells

Self‐Regulated Growth of Large‐Grain Sb2S3 Thin Films for High‐Efficiency Solar Cells

Grain Engineering of Sb2S3 Thin Films to Enable Efficient Planar Solar Cells with High Open‐Circuit Voltage

Phase pure CuSbS2 thin films by heat treatment of electrodeposited Sb2S3/Cu layers

Impact of Sulfuration Time on Properties of CuInS2 Films

Fabrication of phase-pure and large-grained Cu3BiS3 films by a two-stage process for thin film solar cells

Growth of Zn doped Cu(In, Ga)Se 2 thin films by RF sputtering for solar cell applications

Phase composition of the earth-abundant Cu2SnS3 thin films with different annealing temperature and its effects on the performance of the related solar cells

Investigation of Cu2ZnSnS4 thin film with preannealing process and ZnS buffer layer prepared by magnetron sputtering deposition

In situ solvothermal growth of Cu2ZnSnS4 thin film for counter electrode of dye-sensitized solar cells

An effective combination reaction involved with sputtered and selenized Sb precursors for efficient Sb2Se3 thin film solar cells

Co‐Evaporated CuSbSe2 Thin Films for Solar Cells

Solution-processed In2S3 nanosheet arrays for CuInS2 thin film solar cells

Optimization of CuInGaSSe properties and CuInGaSSe/CdS interface quality for efficient solar cells processed with CuInGa precursors

Thin film solar cells based on Ag-substituted CuSbS2 absorber

The low temperature pyrolysis preparation of In2S3 thin film and its application in Sb2S3 thin film solar cells

Thin-Film Solar Cells Based on Selenized CuSbS2 Absorber