Abstract:To improve the ablation resistance of carbon/carbon (C/C) composites, tungsten (W) coating with thickness of 1.2 mm was applied by atmospheric plasma spraying. The antiablation property of the coated composites was evaluated by oxyacetylene flame ablation experiments. The phase composition of the coating was investigated by a combination of x-ray diffraction analysis and scanning electron microscopy with energy-dispersive x-ray spectroscopy analysis. The ablation resistance of the coated C/C substrates was compared with that of uncoated C/C composites and C/C-CuZr composites after ablation for 30 s. The properties of the coated C/C composites after ablation time of 10, 30, 60, 90, 120, and 180 s were further studied. The results indicated that the mass and linear ablation rates of the W-coated C/C composites were lower than those of uncoated C/C or C/C-CuZr composites after ablation for 30 s. The coating exhibited heat stability after 120 s of ablation, with mass loss and linear ablation rates of 7.39 × 10 −3 g/s and 3.50 × 10 −3 mm/s, respectively. However, the W coating became ineffective and failed after ablation for 180 s. Three ablation regions could be identified, in which the ablation mechanism of the coating changed from thermochemical to thermophysical erosion to mechanical scouring with increasing ablation time.

Effect of W Content on the Ablation Properties of W-ZrC Composites Synthesized by Reactive Melt Infiltration under Oxyacetylene Flame

Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Effect of Carbide Particles on the Ablation Properties of Tungsten Composites

Ablation Properties of ZrCp/W Composites

Influence of Zrc Content on the Elevated Temperature Tensile Properties of Zrcp/W Composites

Tungsten Joining with Copper Alloy and Its High Heat Load Performance

Ablation of Tungsten Matrix Composites Reinforced by TiC and ZrC Particles

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Plasma ablation behavior of ZrCp/W composites

Outstanding Mechanical and Ablation Resistance of C/C–ZrC–W Composites Prepared Via Slurry Impregnation and Reactive Melt Infiltration at 1500 ℃

Oxidative ablation behavior of W‐coated C/C composites prepared by CVD with heat‐treatment

Ablation Resistance of C/C Composites with Atmospheric Plasma-Sprayed W Coating

Oxidative Ablation Behavior of W‐Coated C/C Composites Prepared by Chemical Vapor Deposition with Heat Treatment

W-ZrC composites prepared by reactive melt infiltration of Zr2Cu alloy into partially carburized W preforms

Microstructure and Mechanical Properties of W-ZrC Composites Synthesized by Reactive Melt Infiltration of Zr2Cu into Porous Preforms from Partially Carburized W Powders

Ablation Behavior of ZrB2–SiC–ZrO2 Ceramic Composites by Means of the Oxyacetylene Torch

Effect of ZrC nanopowder addition in WC preforms on microstructure and properties of W–ZrC composites prepared by the displacive compensation of porosity (DCP) method

Effect of WC content on microstructure and properties of laser-cladded in-situ reactive ZrC/ZrB 2 composite coatings on zirconium alloy

Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

Microstructure and Properties of ZrC–W Composite Fabricated by Reactive Infiltration of Zr2Cu into WC/W Preform