Abstract:In the present work, WC preforms with varied amounts of ZrC nanopowder (0–3.5 vol.%) were prepared using gel-casting base on nontoxic sodium alginate and then reactively infiltrated by molten Zr2Cu through displacive compensation of porosity method. The influence of ZrC nanopowder addition on the relative density, phase composition, microstructure, and properties of the final composites were investigated. The relative density, Vickers hardness, and flexural strength of the resulted composites prepared by reactive infiltration first increased and then decreased with increasing fraction of ZrC nanopowder in WC preforms. When the added fraction of ZrC nanopowder was 1.5 vol.%, the relative density, hardness, and flexural strength of the resulted composite reached their maximum values of about 97.3± 1%, 10.9± 0.3 GPa, and 503± 3 MPa, respectively. Fractography studies revealed that the fracture mode of composites was predominately intergranular. The W-ZrC composite was ablated by an oxyacetylene flame for 60 s. The mean value of mass and linear ablation rates of the composite were 2.1 ± 0.1 mg/s and 2.9 ± 0.3 μm/s, respectively. W-ZrC composites fabricated in complex and near net shapes at modest temperature and at ambient pressure by a reactive infiltration process can be utilized in aerospace applications.

Microstructure and Properties of ZrC–W Composite Fabricated by Reactive Infiltration of Zr2Cu into WC/W Preform

Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Microstructure and Mechanical Properties of ZrCW Matrix Composite Prepared by Reactive Infiltration at 1300 °C

Microstructure and Mechanical Properties of W-ZrC Composites Synthesized by Reactive Melt Infiltration of Zr2Cu into Porous Preforms from Partially Carburized W Powders

W-ZrC composites prepared by reactive melt infiltration of Zr2Cu alloy into partially carburized W preforms

Preparation of W/ZrC Composites by Reactive Melt Penetration

Microstructures and Mechanical Properties of ZrCP/W Composites at Room Temperature

Effect of ZrC nanopowder addition in WC preforms on microstructure and properties of W–ZrC composites prepared by the displacive compensation of porosity (DCP) method

Microstructure and mechanical properties of 20Wf/30ZrCp/W composite

Microstructure Evolution and Properties of Tungsten Reinforced by Additions of ZrC

Outstanding Mechanical and Ablation Resistance of C/C–ZrC–W Composites Prepared Via Slurry Impregnation and Reactive Melt Infiltration at 1500 ℃

Microstructure and Mechanical Properties of Intragranular W-Cu/TiC-ZrC Composite Prepared by Reactive Melt Infiltration at 1300 °C

Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties

Processing of ZrC-W composites produced by reactive melt infiltration method

Toughening Mechanisms and Interfacial Bonding of W-ZrC Composites

Fabrication and properties of Cf/ZrC‐SiC‐based composites by an improved reactive melt infiltration

Effect of ZrC Particle Size on Microstructure and Room Temperature Mechanical Properties of ZrCp/W Composites

Microstructure and Mechanical Properties of ZrC-W-Cu Composites Prepared Via Gas Pressure Infiltration

Effect of Zrc Content on Microstructure and Properties of Tungsten Materials

Microstructure and Mechanical Properties of ZrC x -NbC y -Cu Composites by Reactive Infiltration at 1 300 °C

Microstructure and Mechanical Properties of ZrC-TaC Composite Fabricated by Displacive Compensation of Porosity at 1300 °C