Abstract:The Journal of Strain Analysis for Engineering Design, Ahead of Print. In the present work, the process chain in tube production by roll forming of the steel 34MnB5 was examined in more detail. The process chain consisting of the steps (i) roll forming, (ii) HFI welding, and then (iii) straightening and final calibration was mapped using the finite element method. In addition to the pipe geometry, the residual stress distribution was considered as an essential target value for the assessment of the performance of the tubes under service conditions. The objective of the project is to describe the manufacturing process and thus the processing induced residual stress distributions as realistically as possible. For a more detailed characterization of the process and above all for the validation of the numerical simulations, experimental residual stress analyses were carried out for the final state of the tubes using complementary analysis methods. The contour method was used to determine the 2D-distribution of residual stresses across the transverse and longitudinal sections of the manufactured pipes. These measurements were supplemented by local residual stress analyses using the incremental hole drilling method and X-ray residual stress analyses. The work thus pursues both a methodical approach to the analysis of the internal stresses induced by the process using complementary methods and also a manufacturing approach to the analysis and evaluation of the production chain. In particular for the axial components of the residual stresses, it can be shown that experimentally determined residual stresses correlate well with the numerically calculated values. The contour method is excellently suited to monitor the uneven distribution of the internal stresses over the pipe cross-section. The results of the simulation show that the overall residual stress distribution that is determined using the contour method mainly results from the plastic strains introduced by the roll forming process. X-ray and hole drilling analyses are shown to be more suitable for measuring locally present residual stresses at defined positions on the outer tube surface. In this way it can be shown that the simulation approach described provides an accurate model of the process.

Determination of Repair Weld Residual Stress in a Tube to Tube-Sheet Joint by Neutron Diffraction and the Finite Element Method

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Effect of Tube Arrangement on the Welding of the Tube-to-Tubesheet Joint of Shell-and-Tube Heat Exchangers Using the Finite Element Method

Effect of Welding Sequence and the Transverse Geometry of the Weld Overlay on the Distribution of Residual Stress in the Weld Overlay Repair of T23 Tubes

Finite element simulation of multi-layer repair welding and experimental investigation of the residual stress fields in steel welded components

Effect of welding residual stress on the performance of CFST tubular joints

Residual stresses evolution during strip clad welding, post welding heat treatment and repair welding for a large pressure vessel

Electromagnetic Ultrasonic Measurement for Welding Residual Stress Detection - Comparison Between Experiment with Numerical Simulation

Effect of Repeated Weld Repairs on Microstructure and Mechanical Properties of Heat-Affected Zone in CA6NM Stainless Steel

Residual stresses at weld repairs and effects of repair geometry

Numerical and Experimental Analysis of Dissimilar Repair Welding Residual Stress in P91 Steel Considering Solid-State Phase Transformation

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Experimental and Numerical Simulation to Study the Reduction of Welding Residual Stress by Ultrasonic Impact Treatment

Effect of Welding Defects on Mechanical Properties of Welded Joints Subjected to Temperature

Role of residual stress in the failure of HF-ERW welded tubes

Evolution of welding residual stresses during cyclic tests in welded tubular joints

Numerical Investigation on Stress Distribution and Evolution in 9cr/2.25cr Dissimilar Welded Rotor Undergoing Welding and Heat Treatment

Effect of repair welding on the fatigue behavior of AA6082-T6 T-joints in marine structures based on FFS and experiments

Effect of Strain Hardening Constitutive Relations on Weld Residual Stress Simulation of Dissimilar Metal Weld

Experimental and numerical analysis of residual stresses induced by the manufacturing process of longitudinal welded tubes

Full-Field Eigenstrain Reconstruction For The Investigation Of Residual Stresses In Finite Length Weldments