Abstract:The Journal of Strain Analysis for Engineering Design, Ahead of Print. In the present work, the process chain in tube production by roll forming of the steel 34MnB5 was examined in more detail. The process chain consisting of the steps (i) roll forming, (ii) HFI welding, and then (iii) straightening and final calibration was mapped using the finite element method. In addition to the pipe geometry, the residual stress distribution was considered as an essential target value for the assessment of the performance of the tubes under service conditions. The objective of the project is to describe the manufacturing process and thus the processing induced residual stress distributions as realistically as possible. For a more detailed characterization of the process and above all for the validation of the numerical simulations, experimental residual stress analyses were carried out for the final state of the tubes using complementary analysis methods. The contour method was used to determine the 2D-distribution of residual stresses across the transverse and longitudinal sections of the manufactured pipes. These measurements were supplemented by local residual stress analyses using the incremental hole drilling method and X-ray residual stress analyses. The work thus pursues both a methodical approach to the analysis of the internal stresses induced by the process using complementary methods and also a manufacturing approach to the analysis and evaluation of the production chain. In particular for the axial components of the residual stresses, it can be shown that experimentally determined residual stresses correlate well with the numerically calculated values. The contour method is excellently suited to monitor the uneven distribution of the internal stresses over the pipe cross-section. The results of the simulation show that the overall residual stress distribution that is determined using the contour method mainly results from the plastic strains introduced by the roll forming process. X-ray and hole drilling analyses are shown to be more suitable for measuring locally present residual stresses at defined positions on the outer tube surface. In this way it can be shown that the simulation approach described provides an accurate model of the process.

Role of residual stress in the failure of HF-ERW welded tubes

Estimation of Residual Stresses by Nanoindentation in an Experimental High Strength Microalloyed Steel Subjected to Rapid Thermal Cycles

Experimental and numerical analysis of residual stresses induced by the manufacturing process of longitudinal welded tubes

A practical analysis of residual stresses induced by high-frequency mechanical impact post-weld treatment

Welding residual stress behavior under mechanical loading

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Numerical Investigation on Stress Distribution and Evolution in 9cr/2.25cr Dissimilar Welded Rotor Undergoing Welding and Heat Treatment

Residual Stress Analysis in Pipe Welding ASTM A106 Grade B Using FEM Simulation

Effect of Tube Arrangement on the Welding of the Tube-to-Tubesheet Joint of Shell-and-Tube Heat Exchangers Using the Finite Element Method

Hydraulic Bulging and Failure Analyses of Wire Arc Additive Manufactured Steel Tubes

Residual Stress Formation and Distortion in Austenitic AISI304 Steel Pipe Weldment with Consideration of Latent Heat using Novel Prescribed Weld Temperature

Failure behavior of resistance spot welded advanced high strength steel: The role of surface condition and initial microstructure

Effect of welding residual stress on the performance of CFST tubular joints

Evolution of welding residual stresses during cyclic tests in welded tubular joints

Three-dimensional finite element modelling of welding residual stresses of medium carbon steel pipes with consideration of solid-state austenite-martensite transformation and post-weld heat treatment

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

Multiphysics Study of Thermal Profiles and Residual Stress in Welding

Development and comparison of residual stress measurement on welds by various methods

The effect of residual stress on fatigue life of welded Cruciform joints of 16MnR for train bogie

Effects of Welding and Constraint Conditions on the Welding Residual Stress and Hardness of Type 316 Stainless Steel Pipe

Numerical and Experimental Analysis of Dissimilar Repair Welding Residual Stress in P91 Steel Considering Solid-State Phase Transformation